Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic -- Hot Rod Forum

Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Transmission - Rearend> rear end ratio
User Name
lost password?   |   register now

Thread: rear end ratio Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Please select your insurance company (Optional)


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
02-02-2003 02:50 PM
dmorris1200 Haven't seen one yet but I would still want to average out a bunch of revolutions instead of relying on one. I have seen some pretty sloppy rears in my day, one turn could be 3.50, 3.70, etc. The more turns you do the closer your average will be. Just my opinion. And I still say (which was my first answer in the other post I linked) the best way to know for sure is to simply pop off your rear cover and count teeth. If deuce_454 had followed the link I posted he would have seen that and wouldn't have found it neccessary to post what was already posted before about counting them. This isn't rocket science deuce.

[ February 02, 2003: Message edited by: dmorris1200 ]</p>
02-02-2003 02:44 PM
BstMech Hey dmorris- they make wheel that you put on your axle flange that determines the gear ratio with one turn of the drive shaft (looks like a cam degree wheel). If you see one of these, notice that the open diff scale is exactly twice the degrees on the scale to get the same reading as a posi diff.
02-02-2003 02:25 PM
dmorris1200 I have personally done the spin once method and had it not work. I even double checked the gears when I took the rear apart. I think that is why you need to rotate 10 or more times and then use an average for a more approximate guess and also keep in mind what was posted about whether or not it's posi or open. Say what you will but I have witnesed it not be accurate with my own two eyes, and I'll believe them over anything.
I think you should stay in school deuce_454, you may learn something.
And what about a beat up old rear with excessive backlash, I guess that's not a variable in the old spin it once method.

[ February 02, 2003: Message edited by: dmorris1200 ]</p>
02-02-2003 02:00 PM
BstMech Check out how an open differential works, it gives a 2:1 ratio when one wheel is held stationary. If you don't hold one wheel still, you will get mixed readings. Open or posi diff, those are the variables. I think dmorris was more talking about the different methods as being all the different variables.

[ February 02, 2003: Message edited by: BstMech ]</p>
02-02-2003 01:31 PM
deuce_454 there are NO other variables period. the rearend is a gear. if you turn one part of the gear, the other part will rotate proportionally faster or slower dictated by the ratio. if counting revolutions is not accurate or practically possible, you can also remove the rearend cover and count the teeth on the gears, example; 11 gears on the pinion, 41 on the ring: 41/11=3.7372727 (3.73) this will also be stamped on the ring gear.. come on dmorris1200 this is not rocket science
02-02-2003 12:37 PM
dmorris1200 It is more involved than just spin the tire and count. That doesn't work cause there are variables. Refer to this older post on this same topic.

<a href="" target="_blank">How do you tell rearend Ratio</a>
02-02-2003 12:19 PM
ModelAMan Monte Carlo is right. Doesn't matter how big the wheel is, just one rotation of the wheel and count how many times the driveshaft turns.
02-02-2003 11:44 AM
83GrandPrix Well wouldn't that all depend on the wheel size and tire size.I wouldn't see that ever working out unless it was all stock and even then it would hard. I don't know much about this topic but it did sound wierd.
02-02-2003 08:23 AM
87 Monte Carlo LS why dont you jack it up and turn the wheel and see how many times the driveshaft turns.
02-02-2003 03:42 AM
dklong check the opotion sheet again it should say the gear ratio. if you cant find it check with your gm dealer,for your 81 gm 3/4 ton
02-01-2003 11:11 AM
rear end ratio

can any one out there tell me if it is possible to get rear end ratio out of vin#? If so here is my vin#2GOGK24T1B1 147153, ANY HELP GREATLY APPRECIATED

[ February 01, 2003: Message edited by: kors86chevy ]</p>

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -6. The time now is 04:56 AM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 1999 - 2012. All Rights Reserved.