Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> thoughts on this 427 combo
User Name
Password
lost password?   |   register now

Thread: thoughts on this 427 combo Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
02-17-2006 11:21 AM
2wld4u considering the rectangle port heads I would go with a 454, Im currently in the middle of just such a project, the car is a 65 chevelle, 10:1 454, with the large oval port heads. I pocket ported the heads, and have installed 2.25x1.88 valves and shaved the heads to attain 10:1. the cam is a ISKY mega HDY 280, the intake is a weiand action+ (due to hood clearance) whitch I gasket matched and did some minor cleanup on. The whole idea was a stump pulling monster that he could drive to car shows etc.. the car has a 12 bolt, 4.10 gears, and 275/60/15 rear tires. Th350 and a TCI breakaway torque converter. this combo should pull like a freight train to 5800.

I will add photo's of this project soon, along with the performance.

2wld4u
02-17-2006 11:03 AM
bigwildgrin
thoughts on this 427 combo

I'd appreciate anyones thoughts on this engine combo. Only the block has been purchased, so its not too late for me to change anything. Here's what I'm planning:

I have a big block chevy block, bored .30. I'm thinking a steel crank and rods, forged pistons. I can get this combo in about any compression ratio; I'm thinking about 10:1. A Comp Cams .294 duration with .595 lift, solid lifters, edelbrock aluminum rectangle port heads, edelbrock dual four intake with two 600 carbs. Headers of course. All this will go into a corvette that weighed 2100lbs with a small block in it and a near empty tank. The tranny is a muncie m21 and the rear is a 4:11, although this is much too low for my taste and will be changed, probably to a 3:08. The car does not have power brakes, but the headlight doors and wiper doors are vacuum. It would be okay if I had to rev the engine a little to get the vacuum doors to open, just so long as they will open. This is a street car, but it's not going to be driven by grandma.
And also as a final thought, I have a 454 forged crank, new in the box that I was considering using instead of buying a 427 crank. Any thoughts on this with the same combo?

thanks in advance

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 06:21 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.