Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Transmission - Rearend> 1989 4l60( 700r4) shifts from 2nd to neutral
User Name
Password
lost password?   |   register now

Thread: 1989 4l60( 700r4) shifts from 2nd to neutral Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
04-07-2006 12:51 AM
madamstn
changes

I guess I have to go with the information gathering guys. I would not think you could feel free in a big RR to put in guages-. but nothing like permanent guages. Some monitor the areas they work most in or most familiar with. If they are there full time you learn what happens in all circumstances- then you will know when something changes. Analog guages not digital leds. I had a Gmc truck years ago,ocassionally it would get hot . stuck a temp guage sensor in the hose out of the thermostat. Once in a while I would get a big temperature needle jump, even out , then in a while the engine would over heat, The needle jump was a steam bubble passing over the sensor. By being there, I could predict overheating and watch the other things that were happing as it progessed to the point of overheating. I have forgotten what was wrong, But not the lesson,Got a problem Make a plan on how to solve it. just a word. mark
04-06-2006 07:40 PM
Riby Thanks eliotmansfield,

I know i haven't responded for a while, but i've learned a little more about the problem know
I'm starting to think that is more along the lines of the filter like you say.

However, What i've noticed now is that, i can go full out in D and have no problems, but when its in OD, and the revs get up there is when the problem comes back.
Possibly the way it routes the fluid in D, stop it from starving?

I'll have to do a fluid and filter change and see where that gets me.
Thanks for the help
12-10-2005 02:33 AM
eliotmansfield reason for asking about filter related stuff, is just wondering if its getting starved of oil at high rpm's and at a point where it needs good clamping pressure for the 2-3 change. Ive got a pressure guage connected to the main line tap permanently - just something I like to see.
Given the intermittant nature, its going to be quite hard to track down.
12-10-2005 01:14 AM
Riby RE: And the filter is clean and seated correctly ?

Is seated correctly. Possibly not the cleanist. How would this effect only third?

RE: Correct filter for depth of pan?

Still using stock oil pan

RE: only one o-ring around the neck or inside the pump inlet?

This one i don't know either way for sure. But sounds as if it would cause more problems then just this?

As far as the guage goes, i'd like to set one up sometime. Only conflict i have is since it only happens ever once in a while i'd have to fluke to have this problem with the guage hooked up.

Recently i haven't had any problems with it. Actually not once since my orginal post (over a month ago). Just to give you an idea of the frequency and the irregularity of it

Do you think that there is possibly a valve sticking in the valve body or something along this line.
12-09-2005 12:04 AM
eliotmansfield Other thoughts:
And the filter is clean and seated correctly ?
Correct filter for depth of pan?
only one o-ring around the neck or inside the pump inlet?

Get yourself a pressure guage and compare main line pressure and 3rd gear pressure via the test ports [at the point when the problem occurs]. I use a std guage from a compressor with correct fittings.
12-08-2005 07:31 PM
Riby Vicrod: Fluid level is good now, i've check it several times (I have had problems from being low on fluid before but the charaterisics were much differnt.) If any thing i would say that is on the higher side.

Eliot mansfield: Fluid is the cleanist that i've seen it, and does not smell burnt.
12-08-2005 04:00 PM
eliotmansfield 3-4 clutch pack on its way out? - inspect the trans fluid, what colour - does it smell burnt?
12-04-2005 06:06 PM
poncho62 moving there......
12-04-2005 05:42 PM
Henry Highrise Welcome to Hotrodders. This forum is for introductions. If you will place your question in the Transmission forum then the people that know about transmissions could answer it for you.
12-04-2005 05:33 PM
vicrod Had the same problem. It's not neutral, there not enough fluid to operate the servo.
When I installed my trans I filled it with fluid. Running Hot.
Apparently I wasn't very careful because when I had the shifting problem you describe I rechecked the fluid.
When I added (1-1/2) quarts, it shifted OK.

Check it out.

vicrod
11-05-2005 02:01 AM
Riby
1989 4l60( 700r4) shifts from 2nd to neutral

I have an 1989 4l60 (700r4) and from time to time it shifts from 2nd gear in what i would describe as neutral. I have rebuilt the transmission and it has parts of a B&M shift kit and a Transgo shift kit in it. 95 percent of the time it functions just fine, shifts quick and hard through all gears. When i do have any problems it is the 2-3 shift and my foot is in it, i'd say at least 80 percent throttle. All i do to fix it is i let my foot off the gas and it slips into gear and away i go. It tends to have problems more often when it's cold. I'm not overly concernd about it, but i'd like to fix it. Kinda make me feel like an idiot when i go to pass someone and it shifts into neutral and just revs the engine haha

If anyone has any ideas or suggestion i'd like to hear them.
Thanks
Ryan

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 07:45 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.