|10-11-2008 11:10 PM|
|11-23-2007 02:56 PM|
94 Malibu starting problem
My son has a 95 Malibu automatic v-6 and when you start it and drive and then stop it some times not all the time it will not start back up. The engine turns over just fine and the longer you try to start it the longer it will take to start. On the other hand if you go shopping for a while and then come back to the car it will start right up again. It's got me scratching my head with this problem because I'm not sure where to look for the problem and the engine runs smooth and good.One would think if was in the ignition system I would have a miss or it would be there all the time but now I'm also dealing with a computer so I thought someone out there might have run across this problem before and save me some time on what to look for or just take a stab at what you would do two heads are better then one,,thanks,,Joe
|05-02-2007 12:10 AM|
answer in your other post..
I guess this was moved here..
|05-01-2007 10:03 PM|
hi everybody,maybe someone can help me with this.i have 75 gmc pickup that won't start.cranks over but won't start.if i run a power wire from the battery to the distributor cap terminal,truck fires right up.have changed ignition switch and checked wire to fuse block and tried changing fuses,no luck.i'm overlooking something but not sure what.any help would be appreciated.thanks,i hope i put this post in right place
|04-28-2006 12:25 AM|
Hi Doc, me again:
the car is running normal, no blown fuses, no melt cables so far. At daylight, kind of power cut off for a moment when footed, normal when revving slow. No problem at nigh-time (headlights on).
Installed a resistor but I think I got a wrong one (rated 1,6 ohms), the car didn't start, took it off.
|04-27-2006 03:27 AM|
That would be on the secondary side of the coil..not too much to worry about there if you have 8 MM spiral core wires and proper gapped plugs (around 45)
The primary is the side pulling around 20 amps..The + side..It may not be compatible with your Ignition module I really couldn't say for sure..you need to check the instruction sheets for both units for compatibility.
A ballast resistor may not be required for that coil either, another thing to check on your data sheets, It could just make it run worse..At the very least, It will defeat the purpose of why you put the upgraded coil on there to begin with.
|04-27-2006 01:56 AM|
Thank you Doc ĦĦĦĦ (amazed for your late night reply)
I am very amateur, but surfing through the posts (lots of yours) have helped me a lot (not too many info sources here en Chile).
If I get it right, that combination will make 20 amp on the spark plug wires, with risk of freeing them. Will a ballast resistor cure this?
I took the car for a 15 min ride, after installing an MSD 5900, the Flame thrower II coil, the Taylor SST wires (Ignitor I was installed before) and runs great.....so far.
By the way, I installed all this trying to low HC omissions to pass next control, so any help on how to kill HC will be greatly appreciate also.
Long live Chevy'sĦĦĦĦĦ
69 camaro 307
69 C-10 six-liner
67 elky 283??
|04-27-2006 12:28 AM|
Not sure I know what your asking..
But if referring to the primary side of the coil it will be 20 amps..12v divided by 0.6=20...
If thats the case, most stock ignitions are designed for about 10 amps..the wire gauge will be undersized and could cause a meltdown in the harness or fire, and if fused it will keep blowing fuses..
|04-27-2006 12:11 AM|
ignition max amp
I make a mistake. Bought a Flamethrower II coil having an original Ignitor. There is a warning on the coil not to use together (because the final ignition amp will be too high?
What will be the max amp recommended (69 gm 307, taylor braided wires, approx 12 volts on the coil + when running, coil 0,600 ohms)?
What damage may occur if used?
Appreciate your help.
|02-12-2006 05:59 PM|
Here is the Diagram for 71 - 78 With Electronic Ignition,
The V8 is on the right side, The Brown from the Dizzy and the Green /white from the Dizzy go to the module brown and green /white wires .. as do the pink (duel Ballast resistor) and black yellow (module), from the coil
Sorry for the crappy drawing..
Disregard the left side of the photo, It's V6.
Maybe this is a bit better I redrew it in PSP....It's still hard to read..
|02-11-2006 05:08 PM|
1969 318 dodge
hey can you tell me how to wire the electronic ign. had an engine fire in this old dodge van.now
|11-26-2005 09:53 PM|
Added to Hotrodders Knowledge Base
This discussion has been added to the Electrical Discussions category of the Hotrodders Knowledge Base.
--For the main page of the Hotrodders Knowledge Base, click here.
--For more information on the Hotrodders Knowledge Base, click here.
--For information on becoming a Hotrodders Knowledge Base Editor, click here.
|04-05-2005 07:12 AM|
|Neophyte||I have a 91 SBC 350 TBI with small square coil just outside the dizzy. Trying to start I have no spark. The coil has 4 wires on 2 plugs: plug 1 - Pink for power, white for tacho. Plug 2 - red wire and white wire (if I remember right). How can I check if the coil or the dizzy module is faulty? PLEASE HELP!|
|03-23-2005 03:43 PM|
|09-14-2004 09:51 PM|
67 Mercury - 302
Drug this thing home on Saturday and am not getting fire. Getting voltage to the coil, the points are firing but cannot get anything out of the cap. I say that, have only tried grounding out a plug out of the engine and got a bunch of nothing. New coil, cap, button, wires, and plugs.
Any ideas? Been so long since I messed with points I do not remember how to test half of this stuff!
|This thread has more than 15 replies. Click here to review the whole thread.|