Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic -- Hot Rod Forum

Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Body - Exterior> OEM Primed Bumper Cover primer/sealer?
User Name
lost password?   |   register now

Thread: OEM Primed Bumper Cover primer/sealer? Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Please select your insurance company (Optional)


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
05-09-2006 09:59 PM

should have this ready to buff by friday
05-08-2006 05:37 AM
jcclark If you clear over scratches chances are you'll still see them,
even after sanding the clear.
Most time the clear enhances scratches.
I would sand the base lightly with a finer grit (I use 600)
to get rid of the scratches then re-base before the clear.
05-06-2006 01:21 PM
tommygunns damn I picked up a quart of 222s
anyways...I'll use it when I do the hood and fenders etc.

well I sanded the basecoat and flattened the runs on the side, cleaned it real nice and shot another coat of sheet on chromabase says it can be re-coated on itself within 24 hrs.... So the bumper is basically smooth and a little orange peeled on top a bit.....I think I'll adjust the fan smaller next time if I re-do it

problem now is I can see a SMALL bit of sanding scratches (probably 200 grit) here and there...... kinda minor but...what is the best way to get them out??

or could I just clear it and spend a day with some 1000 and some water??

I'm learning!!! Thanks Mr.Clark for the help
05-05-2006 05:16 AM
jcclark You're probably putting the base on way to wet.
Basecoat is not suppose to be shiney. You have to really
pile it on to get a run. Spray it just wet enough to get it smooth,
it dries fast and is suppose to look dull.
If you sand it to get it flat and don't sand through to the plastic,
you don't need any adhesion promoter.
05-04-2006 07:39 PM
tommygunns ok so I screwed it up.....basecoated with chromabase in a low light garage and got some curtains....

I just spent 2 hours sifting thru pages here and it sounds like I am going to have to sand them out and apply 222s midcoat adhesion promotor and shoot again

05-03-2006 05:31 AM
tommygunns will do ....I removed all of the rattle can primer and will hit the bumper with adhesion promotor then 2k it....and yes I'll have to block it out a bit so I am not done with the sand paper just yet.....hee hee
wish me luck
05-02-2006 04:59 AM
jcclark One more thing, if you cover it with 2k you need to sand it before
basecoating for max adhesion.
05-01-2006 04:40 PM
tommygunns awesome thanks for the help!
it will be 70 degrees low humidity on thursday when I plan to base coat...WOO HOO!!
can't wait
05-01-2006 07:27 AM
jcclark The best thing to use on bumpers is epoxy primer.
The next best thing would be a 2K primer, I use it most when
needing to fill scratches. It sands easier than the epoxy but epoxy
can also fill small scratches.
With either one you don't need an additional sealer, the primer is
ready for paint and both of them seal pretty well.
In either case I would remove all the rattle can primer, it's the weak link.
04-30-2006 11:05 AM
OEM Primed Bumper Cover primer/sealer?

I have done a lot of searching here on the forum but just want to get a clear heads-up on this situation ...

I have done some modifications to this new OEM bumper which required the use of adhesion promoter then Duramix then adhesion promoter again.

I then spot primed the areas with a rattle can (1K) primer..and got it flat and smooth

My questions would be....

- Should I sand the 1K primer off and shoot the bumper cover with a 2K primer?
Then seal it?
Which primer will work on flexible bumper covers?


Could I just seal it up with some Prime N' Seal and go to base coat??

I'll post up pictures as soon as I complete

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -6. The time now is 07:15 PM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 1999 - 2012. All Rights Reserved.