Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic -- Hot Rod Forum

Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Suspension - Brakes - Steering> Welded Front Clilp
User Name
lost password?   |   register now

Thread: Welded Front Clilp Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Please select your insurance company (Optional)


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
04-10-2002 02:47 PM
F-1Rodder Phat is giving you good information, but I feel that the clip is too wide generally. If you put disc brakes on, this will increase the width 1 1/2". Next, you will be buying FatMan Fabrications narrowed A arms.
04-08-2002 10:15 AM
Phat Hey one more thing if you got that far.Get the rear end set to the height you need it. Now check the lower control arms to the ground...are they level(front to rear,tipped back a degree or so is ok but forward is a no no) Also the take the springs out and put a piece of threaded rod were the shocks go or weld straps on the lower a-frame to frame with the lower a-frame level side to side( center of ball joint lower than the inner pivot for the a-frame) That will tell you if the clip is on to low or to high for you . Good luck
04-08-2002 08:41 AM
beetle9 Problem cured. I took Phat's advice and removed the clip. I did not cut it off however. I merely took my air cut off tool and cut off the old weld, loosened the clip up and squared it with the old ford frame. It is now within 1/8th of an inch from any measurement point. Now I will re-weld and shouldn't be any problem. I reinstalled the fron fenders and running boards on the frame and everything is centered. Life is now good again. Thanks Phat.
04-06-2002 10:11 AM
Phat I will say this much. If the guy could not get the clip even on straight....throw the frame away or cut the clip off and start fresh. The measuring and welding is the easy part of the clip. To do a clip properly it must have a body on the car...with front fender.Look at the wheels in the wheel opening with the clip tacked. now blow it a part and finish weld it. Did you check to see if the track width was ok?? I really think its to wide for a 35 drum brakes are a little narrow but if you change to disc's its wider.(i could be wrong on this one cause i dont do clips anymore) get the old tape measure out..start fresh.
04-06-2002 09:45 AM
4 Jaw Chuck Air arc works good too. Just like erasing with an eraser.
04-06-2002 08:47 AM
Welded Front Clilp

My 35 tudor ford sedan has a nova front clip grafted on. When I pulled the body off, I found that it is not perpendicular with the body. Its about one inch short on one side. I guess that's what I get for buying the shell someone else already botched up. The old ford frame is slid in side the nova neatly and welded on the exposed edge. I'm thinking I can either grind off the old weld or get someone who is much better with a torch than me to take away most of the old weld. If i can seperate the two, I can square the nova clip with the 35 frame and everything would be hunky dory. Anyone out there have any better suggestion or advice? I feel this is my only hope for saving the frame.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -6. The time now is 07:48 AM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 1999 - 2012. All Rights Reserved.