Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic -- Hot Rod Forum

Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Suspension - Brakes - Steering> vega steering box stiff to rotate
User Name
lost password?   |   register now

Thread: vega steering box stiff to rotate Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Please select your insurance company (Optional)


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
05-28-2006 08:20 AM
pcoghlan thanks for the input Mikey.

I will leave it alone rather than screw with something that works!
05-28-2006 08:05 AM
powerrodsmike There is nothing wrong with that box, That hard spot is supposed to be there.

That "tightness" is what helps keep your car from wandering when you are going in a straight line. That is why it is important to set up your steering linkage so that the box is centered.

There is actually a torque value in the book, (I have a factory manual for a vega, how weird is that?), that specifies the amount of torque to pull the steering wheel over the center. If I remember correctly the value is 8-16 INCH pounds max @ the steering wheel with the pitman arm removed. The same value with the steering gear removed is supposed to be 7-8 inch lbs (including thrust bearing preload of 4 in-lbs) . The torque is supposed to be measured with a dial type torque wrench of no more than 50 inch lbs. Try finding one of those LOL.
On a used box I would not set it that tight. I will post up the procedure if you want.

If I were you I would leave it alone unless it is extra tight or really loose.

Hope this helps, mikey
05-28-2006 07:34 AM
vega steering box stiff to rotate

While I had my '29 Model A up in the air and Vega steering box disconnected from everything I noticed an issue.

The steering wheel would obviously rotate very easily BUT there was a point when the box was mid-way beteen locks that it stiffened up. It wasnt massivly stiff but it stopped and required a little pressure to encourage it though the point and it then loosened back up again. It did this in both directions.

I could spin the wheel from one lock and it would rotate 2-3 times till it arrived at this central point and stop, I would encourage it past the stiffness and again it would spin feely till the opposite lock.

The stiffness isnt something I can really detect now it is back on the road but I am not sure if this means I should rebuild/inspect the box or whether it is normal? I am confident the stiffness is experienced at the exact point the box is mid-way between locks.


Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -6. The time now is 04:09 AM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 1999 - 2012. All Rights Reserved.