Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Transmission - Rearend> Turbo 400 trans speedometer gear?
User Name
Password
lost password?   |   register now

Thread: Turbo 400 trans speedometer gear? Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
06-19-2006 05:42 AM
Pro Street Thanks guys!
I will see if I can come up with a puller.
06-18-2006 09:02 PM
Deuce
Quote:
Originally Posted by Crosley
the photo Deuce has posted is not indicative of a t-400 tranny.
TRUE ... but I posted it to show the relationship of the two gears.
06-18-2006 05:31 PM
Crosley the photo Deuce has posted is not indicative of a t-400 tranny.


The speed-O bullet on a t-400 is in the main case section, not the tail housing

You will need some type of a narrow puller to reach up inside the trans pull off the steel speed-O gear on the t-400 output shaft once the tail housing is off the trans.

I've built a U shaped puller with long legs in the past to pull off metal press on type of speed-O gears. Slip the U shaped around the back of the gear , then thread the puller down onto the output shaft .... the gear slides off. Some times a bit of heat from a propane torch helps the gear to pull off easier.
06-18-2006 05:17 PM
Pro Street I have had the tail housing off before.So that will not be a problem.The problem,is the gear pressed on the shaft?If it is I will have to find a puller that is long enough to pull the gear.
Thanks
06-18-2006 10:49 AM
Deuce Yes ... you can change it ... if you can get the tailhousing off ...



Some vehicles ( custom mostly ) are built so the tailhousing is difficult to remove. Mine is NOT ...

Just remove the driveshaft, and the raise the transmission enough to get the tailhousing clear of the crossmember ( or remove the crossmember ) and remove the speedometer driven gear ... and the tailhousing should come right off ...
06-18-2006 10:23 AM
Pro Street
Turbo 400 trans speedometer gear?

I have a Turbo 400 trans and would like to get the speedometer right.On the main shaft there is a steel gear.I need to change it from a 18 tooth to a 15 tooth.Can I change it with the trans in the car?
Here is a good speedometer gear web site.
Trans gears

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 08:41 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.