Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Compression Testing ....(Hot vs Cold)?
User Name
Password
lost password?   |   register now

Thread: Compression Testing ....(Hot vs Cold)? Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
06-30-2006 01:01 PM
xntrik Actually the difference between hot and cold is usually caused by piston expansion. A cold piston is smaller and rocks back and forth in the cylinder more which allows the rings to not mate to the cylinder walls as well. That is why the oil helps. The ring end gap certainly changes but is not the primary ring compression loss. Some piston materials require a larger clearance and a larger clearance will flop more.

A hot test using the differential pressure testing method is preferred and will indicate where the loss is occuring.

Of course you had all the spark plugs removed and the carb venturi full open when you did the test.
Using the hot cranking method and letting the cylinders pump 5-8 times your readings are acceptable. You should also note how many pumps it took to get the highest reading on each cylinder.
06-29-2006 06:04 AM
302 Z28 The generally agreed upon standard is 10%. You can run another test cold by squirting a small quantity of oil in the cylinder, turn the engine over a few times and recheck the compression. If there is 10% differance then the rings are worn.

You say the engine was rebuilt. Was it bored and new pistons installed, or just a ring job?

Vince
06-29-2006 03:03 AM
Dreadlord well as your engine warms up the metal of the rings will expand giving it less of a gap between the cylinder wall and the piston groove. So it just might be that less compression is escaping because there is less area for it to move through. Your compression is defently better when warmed up but i think that could be just from normal wear on the rings themselves. anyone else have any ideas?
06-27-2006 08:15 PM
white66coupe
Compression Testing ....(Hot vs Cold)?

Hello,

My 289 was rebuilt 4 summers ago now and I'm not sure if my rings are still seating.

The reason I say this is there is a difference in the hot vs cold readings.
Basically the "cold" readings are:
151,149,136,148,155,150,140,133

The "hot" readings are:
160,160,160,165,152,155,155,150.

Is there supposed to be that much of adifference between the hot and cold readings?

Also, when i squirt oil in the cylinders some of the jump up to 170 and 175.

Does this tell me anything about my rings and if they are seated properly?

Thanks, Greg.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 07:11 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.