Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Interior> Not sure how to tackle seat mount problem
User Name
Password
lost password?   |   register now

Thread: Not sure how to tackle seat mount problem Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
10-29-2006 04:22 PM
Chris B I used some aircraft grade alluminum it worked good
08-22-2006 07:21 PM
home brew That is a great tip on building and mounting that floor plate. Thanks DrChop.
08-22-2006 05:49 PM
DrChop
Make the floor plates...

out of 3" square by 1/4" thickness minimum, and drill/tap the mount hole in the middle 3/8-NF thread. Only ONE threaded hole in the plates. When you know where you want the plates drill your mount hole thru the floor 13/32" and around the hole drill 4 smaller holes at least 5/16" dia. Mount your seat and snug up the bolts into your plates under the floorpan, then rosette or plug weld thru the smaller holes in the floor to anchor the threaded plate directly centered under each mount bolt. Nice and neat.
08-22-2006 06:34 AM
jemo Sam,

ok, I think what I'll do is this....

The seat tracks on the seat frame are 3/4" wide.

I'll buy either 1" or 1-1/4" square bar as a vertical spacer. On both ends of the spacer, I'll cap it with some 18 ga. sheet that I have and maybe reinforce it in the corners.

Thanks for the tip. I'll also be sure to weld another piece of plate on the underside of the floor and maybe weld a nut to the underside plate so that I can take the seats out from the top.

Jeff
08-21-2006 01:38 PM
OneMoreTime On those spacers I use a piece of pipe or tubing to make the spacers..on the washer under the floor pan I use about a 3'x3" pice of 1/8 plate so one would have to about completly disintegrate the car before the seat would come out..One learns about this deal if you have ever been upside down in one of these things..

Sam
08-21-2006 01:16 PM
jemo Thanks Sam,

What would I use as a spacer on the back two mounts that need almost 2 1/2" of rise?

Jeff
08-21-2006 08:17 AM
OneMoreTime
Spacers

what you will find is that once you have figured out just where the seat must go you then driil some holes in the floor pan..then make some spacers that go under each bolt location to make the seat set level..(the way you need it to be)..I would place some large washers under the floor pan in way of the bolts so the seat will be less likely to tear out in the sad and sorry event of a accident..the factory puts bends and kinks in their mounts so the seat just sets in..aftermarket or seats from another car won't have that..

Sam
08-19-2006 10:12 PM
jemo
Not sure how to tackle seat mount problem

My next battle is figuring out how to mount bucket seats in my '56 sedan. When I put the bucket seats on the original, raised pad on the floor....the steering wheel is practically on my chest.

The seat needs to be moved back at least 6" which intrudes on the floor space originally meant for the back seat passenger. With that, each corner of where the seat will mount to the floor is at a different height. e.g. the mount in the front right side (closest to the tranny tunnel) is basically a flat piece of floor so I was thinking to raise it 3/16". Directly behind that, the right rear mount needs to be 2 5/16" tall. Etc. etc.

The replacement seats I have just have two flat bars on the bottom so I need to make a surface that is flat so the sliders on the seat can mount and far enough back so that I am not too close to the steering wheel.

I'm sure a million people have faced this problem. I'm new to car restoration and don't know where to start.

Thanks,
Jeff

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 12:56 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.