Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Body - Exterior> Textured chip guard over surfacer?
User Name
Password
lost password?   |   register now

Thread: Textured chip guard over surfacer? Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
10-27-2006 05:31 PM
bitor
Quote:
Originally Posted by baddbob
None of them are comparable in quality to what the OEM used.
Any idea what VW uses for undercoating? It's the toughest stuff I have seen. I have heard about Wurth being the manufacturer.
10-26-2006 01:48 PM
blacklabzeke THANKS!
10-26-2006 01:18 PM
baddbob It will work no problem, just make sure you give the gravel guard the proper amount of dry time or the solvents being released will keep the Concept from curing. Follow the gravel guard manufacturer's instructions on the can.
10-26-2006 05:39 AM
blacklabzeke I would like to spray the gravel guard and topcoat using SS PPG Concept.
10-26-2006 05:30 AM
OneMoreTime I will have to check but I believe the SPI bedliner product may be what you are looking for in a 2k gravel guard..I know it can be tinted and sticks fine to epoxy primer and one can manipulate the texture..I do not know of any reason it would not work in this case..

Sam
10-26-2006 05:18 AM
blacklabzeke Are there any 2K gravel guards out there?
10-25-2006 08:44 PM
baddbob Yeah, all those producst will work. Just remember they are all a 1K product-basically a lacquer type design so give it plenty of dry time before applying your paint-follow the directions on the can. None of them are comparable in quality to what the OEM used.

Another option if you're just looking for texture is to load your gravity feed gun with a urethane surfacer and turn the airpressure down so it spits, spit the primer on to the desired texture where needed then adjust the pressure up and lay on one light thin wet coat, allow to cure then scuff with a scotchbrite then paint. Sounds crude? It works in a pinch... Bob
10-24-2006 09:40 PM
UR50SLO Sounds like your on the right track!

3M,SEM and U-Pol are all good products. Make sure you give the area you intend to put the gravel gard on a good tooth to grab onto... I would not go less of a grit than 320. You may want to put a coat of primer over the gaurd if your using a light top coat(color). I worry about bleeding when light top coats are used... Just me.
If you prime over the gaurd,you can scuff that area with a 3M pad before paint.. a DA or sand paper would cut down the texture. Which would be ok too if you want that effect. (I'm sure you know this)
Just helpfull tips.. sounds like you already have a good hold on what to do as you've already put all the right products down first
~Scott
10-24-2006 09:21 PM
blacklabzeke
Textured chip guard over surfacer?

I currently have my truck epoxy primed (MP170) with a couple coats of surfacer (MP282) over that. I want to apply textured chip guard on the lower stone throw areas (3M, SEM or gravel guard U-Pol). Is this OK over the surfacer? Are any of these products better than the other? I have done a search and have come up with nothing.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 07:44 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.