Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Interior> How do you build a trunk lid interior panel
User Name
Password
lost password?   |   register now

Thread: How do you build a trunk lid interior panel Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
11-30-2006 08:40 AM
DanTwoLakes Hooligan: Make a pattern to fit where you want it out of something pliable, and drill the holes for the clips. Check out a thread called "interior panels" that's on the interiors bulletin board right now regarding making and attaching panels. I use Au-ve-co long offset clips, #10780. The best way to do this would be to take the trunk deck off and do it upside down. It would be a lot easier that way. Can you do that with your car? If you use 1/8" closed cell foam (landau top foam) to pad the panel, you might want to double up on the panel board so the clips don't show through the finished panel. In other words, the inside panel next to the trunk lid has the holes for the clips, and you put another layer on top of it, making it 1/4" thick. Good luck.
11-30-2006 07:23 AM
Hooligan32
Still have some questions

So if I use the waterboard and preshape it, I will then fit it back to the decklid trim the excess and mark locations for fasteners correct? Should I use a spring type clip and then cover the whole board in 1/8 Landau foam to cover the clips and then upholster or is there a better way to attach clips and upholster. Also when I go to upholster the piece I will need to glue the entire surface as opposed to wrapping it around without glue on the face, like you would a flat panel, right? Sorry for any confusion.

Thanks for your help
11-29-2006 09:09 PM
DanTwoLakes I'm sorry, I left out this part. (sometimes my mind gets way ahead of what I want to say) Curve the panel ahead of time by cutting a slightly oversized blank to form to the shape you want (form it around a large curved surface (55 gallon drum?).) Black waterboard would not require heat to form it, and curves very easily, so it would be a lot easier to use. This is a PERSONAL PREFERENCE, not Gospel According To Dan. Good luck.
11-29-2006 08:54 PM
DanTwoLakes I would use black waterboard for this application. It bends easily and would more than hold up. Also: ABS and PVC foamboard (1/8" thick) will bend and form nicely if heat is applied to them. (Black waterboard is far less expensive, though.) Make sure the bend, (or curve, whatever you want to call it) is more severe than the curve of the trunk lid, so that when the panel is attached it spreads out, not curves in and gets wrinkled up. (Is that last sentence as clear as mud? Sorry.)
Good luck.
11-29-2006 03:16 PM
Hooligan32
How do you build a trunk lid interior panel

If anyone could help I would like to know how you would go about building a panel for the inside of a trunk lid, preferably one that has a large curve in it. What materials do you use and how to do hold the curve so it can be upholstered.

Thanks

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 12:45 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.