Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic -- Hot Rod Forum

Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Body - Exterior> Metal Prep?
User Name
lost password?   |   register now

Thread: Metal Prep? Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Please select your insurance company (Optional)


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
03-21-2007 05:00 PM
adtkart ^1 hit it pretty much on the head. Once you get the metal where you want it, go over the panel with whatever grit the epoxy primer manufacturer recommends, and apply the epoxy. The filler can be applied over the epoxy. If you have some minor rust, you can use Naval Jelly to remove it, clean the surface, sand with the right grit and epoxy.

BTW.. There is a post on removing rust that was done by Randy Ferguson. It is very detailed, and he is a metal working master.

03-21-2007 07:55 AM
61 chevy Do your metal work...epoxy prime for corrosion resistance...then your body filler.
03-21-2007 05:13 AM
Metal Prep?

Iíve rolling fender lips and fixing a bunch of stuff hidden under some bondo on the back of my new project car, and Iím trying to make every effort to prevent future rust.

Iíve had to use the stud welder in a few places to get stuff right where I want it (so far everything I finished shouldnít take much mud, really everything looks like Iím just going to wipe it with a skim coat and go, I doubt that I need more then 1/16Ē anywhere, Iím pretty anal retentive when it comes down to it).

What Iím wondering is if itís OK to wipe it down with some metal prep (or if I run into a spot that had more rust even navel jelly) before I skim it to MAKE SURE that any rust that was there is gone? So far Iíve been using a nylon wire wheel (quickly removed bondo without removing much of anything else so I can see what Iím dealing with first) and a 36 grit roloc to cut down to the bare metal where I have to do some work so the surface has a nice bite to it.

I understand that the phosphoric acid in metal prep can do weird things with body filler (keep it from setting up right I think), but they recommend washing it with water to neutralize it, which makes me think that this is all going on on bare metal that Iíd just be causing rust.

What do you guys do? Am I better off skipping the metal prep, just finishing my stud puller/hammer work, hitting it with the 36 grit again and slap on the filler (not sure how much I trust that to get rid of any surface rust that might start while Iím working)? Maybe 60 grit instead of the 36 just to make sure that the grit actually touches more of the surface? Iíd really feel better if I use some metal prep, but I donít wan to hurt anything that goes over it (and this would be a totally different deal if I had the whole body or even a large section totally stripped).

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -6. The time now is 06:12 AM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 1999 - 2012. All Rights Reserved.