|05-20-2007 09:51 AM|
|onebadmerc||I bought a 4 leg 1000 pound stand from HF last year and bolted my Ford 460 to it with no problems. The stand flexed more than I liked it too but it held up fine. As with my 3 leg 750 pound stand, I will only store empty blocks on it after it fell over with a fully dressed 351C on it.|
|05-19-2007 05:07 PM|
that lime green 350 hanging on the stand is for my sons Suburban, he picked and loves the lime green. I will put a tape measure on that one cause its tall. real tall for me torqin heads & intakes. my uncle made everything over size to fit him cause he was so big. I'm real careful moving that stand with a engine on it, but it rolls real nice even over floor dry and little pebbles. I just keep a eye open when me or my boy is moving it. it rolls nice with a big block buick on it that was the last big block on it. but for a 3 wheel monster it rolls nice. and it has big bearings in the neck, they look like wheel bearings.
|05-19-2007 12:46 PM|
Now THAT looks like an engine stand!!!
I should have qualified my earlier remark by pointing out that he was moving the stand and engine when it tipped.
|05-18-2007 07:16 PM|
my three wheel engine stand has gave No Troble since it was built in the 70s. but I watch the three wheel engine stand when I'm moving it.
|05-18-2007 04:25 PM|
I've got the 1,000# one and it did a good job on the 405 SBC that I just finished. I did cut a piece of 2x4 and use it as a vertical brace under the front end as I loaded the block with heads, water pump, harmonic balancer, etc.
I would probably buy the 2,000# one if I had it to do over again.
DO NOT buy the 3 wheel 750# one. Had a friend that tipped his over with a 350 SBC on it. Luckily, no serious damage (a storage cabinet stopped the fall), but sure scared the bejeepers out of him.
|05-18-2007 03:32 PM|
|jray||Most certainly stay away from the light-duty 3 wheel ones........I had a cheapy 3 wheeled one and after dropping an engine twice I found someone I didn't like and gave it to them!!|
|05-17-2007 06:17 PM|
|matt167||my dad has a 3 wheeler 750 # HF, and it's questionable at best, with a 350 w/o intake and water pump, it wasn't flexy but seemed mighty tipsy. it's only had 1 engine on it, only used to hold the engine to take off intake, oil filter adaptor and water pump, for his 350 crate motor, so I guess it served it's $35 purpose, rental would have cost that.|
|05-17-2007 05:02 PM|
|05-17-2007 02:31 PM|
|jimfulco||4 wheels, widely spaced, and use grade 5 or grade 8 bolts to mount the engine.|
|05-17-2007 09:59 AM|
|tornado-tech||Definitely get one which 4 casters. It is much easier to do a motor. The 3-caster ones tip over real easy|
|05-17-2007 09:32 AM|
Looks like a nifty idea, but you're not going to like having to step over the legs of the cherry picker to get to the block.
|05-17-2007 08:55 AM|
I had issues with the 1000 lb one. I just didn't trust it it flexed so far.
I ended up making a new back plate.
|05-17-2007 08:44 AM|
only thing I don't like about my engine stand (pics one comment up) my uncle built it yrs ago and he was 6'4" + tall so the engine stand is real tall for me i'm just 6' tall) tall torquing heads. but I can live with a Tall Heavy Duty Engine Stand
I liked this idea but have never used one B4.
|05-17-2007 08:35 AM|
spend the extra cash and but the heaviest built one, it will make you happy yrs down the road. a flexing floppy non steady engine stand makes you nervous the whole time a engine is hanging on it. look for a old one someone bought or built yrs ago.
some info here http://www.hotrodders.com/forum/summ...nd+mustangsaly on the 2nd page of that thread is a engine stand my uncle made yrs ago. theres pics of my home made engine stand (its had SBCs BBCs & a pontiac 389 & 400 and Ford 390, Buick 455 on it), looks like the upright neck was fastened to the floor in a factory or machine shop at one time. it has wheel bearing type bearings in the neck. it has a big type wing nut (wing nut is a factory piece that a 3/4 or 7/8 threaded nut with 4" wings) but loosen the wing nut you plus theres a spring loaded leaver that catches in notches on the back of the neck.
look for a heavy duty manufactured or home built engine stand with bearings in the neck.
|05-17-2007 07:15 AM|
|Koolaid||The middle size one with 4 wheels works good for a SBC - wouldn't go any lighter - think they are on sale about once a month for $40 or $45.|
|This thread has more than 15 replies. Click here to review the whole thread.|