Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Engine Kit ?
User Name
Password
lost password?   |   register now

Thread: Engine Kit ? Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
07-14-2007 05:47 PM
DoubleVision If there`s nothing wrong with the stock rods you have then they are fine to reuse and 350 cranks are a dime a dozen. I`ve reused stock rods countless times, as long as there are no spun bearings they`re fine. These rods went into daily driver but weekend play thing vehicles. Never did have one fail me either. The rods in the kit are just reconned, they aren`t going to give you any more power than the ones you have so if there`s not a need for them, especially on a budget build, then why replace what`s not broken? If you have any machine shops in your area ask them if they have any 350 shafts around, they likely do and then some, or a local junkyard. Then you can get a kit from Northern that`s a master kit with a choice of cams just the same, only without the crank and rods. this would more than likely knock a couple hundred off the total of the engine kit that can go elsewhere.
07-14-2007 05:31 PM
Artemis Entreri
Engine Kit ?

As a few of you might remember, I was mulling over a few different engine combinations to put in my 86 Monte SS. I ended up not having internet access for quite a long time, and then I spent almost all of my money I had saved for the car on a vacation, lol. So i'm back with lower expectations of what I want to do.

I've got a block that was bored .030, I got a crank and rods with the block, but the crank ended up not being good, got a nice sliver missing from the base of it. And the rods are just stocker rods. I've been moaning and groaning about having to order all these little things like gasket sets, bearings, caps, all of those things. Scanning across the internet for deals I came upon this:
http://shop.enginekits.com/osb/itemdetails.cfm?ID=90

Gives me everything to put the bottom end together, nice 9.73:1 compression ratio with my Vortec heads. I would order another Cam, but the one that comes with this kit would be a nice one to use in the future when I want to build a mild 350 for my chevy blazer.

For the kit options, id probably get the Cr3 rods, which from what I understand are just recond rods with arp bolts? Lol

So the point of this was what do you guys think of this kit? I know you generally get what you pay for, but im not going to be beating the crud out of the engine on a normal basis or anything and i'm real short on money and still want to do this.

After this kit, all i'd have to do is my valvetrain, intake, carb and top end gasket kit if they dont come with the engine kit.

So for someone building their first engine, trying to save money, would this be a good deal? Basically what do you guys think? Lol

Thanks everyone

P.S.
I want to do something like Combo 78
http://www.ryanscarpage.50megs.com/combos11.html

But higher compression ratio
And probably a bigger cam.
Cam suggestions would be great also. If I was aiming to make 400/450 out of this thing.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 09:47 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.