Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Intake for Dart Pro 1 230's.
User Name
Password
lost password?   |   register now

Thread: Intake for Dart Pro 1 230's. Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
10-15-2007 01:41 PM
duckbutter69 My push rods are 7.850.

After porting are the runners on the Holley Contender 300-36 the same size as the ports on the 230's or are they still smaller?
10-11-2007 05:14 PM
1BAD80 Holley Contender 300-36 fits but should be ported plus I had to trim the 1206 gaskets.
My old 60's cross ram fit also but needed to be ported/gasket matched also.
You may want to read Car Craft Sept 07 issue, it has dyno results with a single plane vs dual plane. Like I said for years,both the same flow.
Did you install longer push rods ?
10-11-2007 04:35 PM
hotrodf1 Hey,

The Weiand Team G is offered in a couple of different versions. Mine has a plenum spacer cast in, but they offer others. I dont' think they are really any taller overall than the dual planes. I like my Team G pretty well. Seems to be pretty decent distribution.

WIth that many cubes and 230s you would want a single plane I think. I use a Team G with my 230s and it worked out well. I also use 1206 gaskets, they fit the best. Had 1207's and they are HUGE. No need, and they are questionable around the ports as the intake sometimes will hardly cover it seems.
10-11-2007 02:42 PM
duckbutter69 I'm looking for a duel plane for hood clearance. If I have to run a single I'll just go with the Dart. Does anyone have experiance with fitting a duel plane on the 230's?
10-11-2007 02:33 PM
barnym17 For that size port a victor jr will probably be a good bet, with 427 cubes a single plane will probably do just fine. What gaskets match your ports? 1205 or 1206?
10-11-2007 02:29 PM
duckbutter69
Intake for Dart Pro 1 230's.

I've got Pro 1 230's on a little M 427. I tried a Torker II intake and the head ports were above the intake flange. What intakes are you guys running with these heads? Are there any duel plan manifolds that match up with the head ports or at least have a tall enough flange on them to cover up the ports? I'm trying to keep low for hood clearance.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 03:40 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.