Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Body - Exterior> 36 Ford Dash
User Name
Password
lost password?   |   register now

Thread: 36 Ford Dash Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
01-08-2008 04:35 PM
joeford
Filling Dash

Thanks for the info....but now you have me thinking that perhaps rather than cutting and filling the three existing holes, perhaps cutting them out to one larger hole....Then fill the one large hole and recut for the new gauges...

My plan is for two larger gauges (tach & speedo) in the dash with any other gauges in a console panel....

Anyway you go, it will be a challenge for me as a novice welder....Hopefully the mig will keep me out of trouble.

Too bad someone doesn't sell a smooth orginal. Thanks again for info....
01-07-2008 07:29 AM
35WINDOW hi joe,

Yes, you could put new pieces in-I have some spray Dykem that I put on the metal, put it behind the holes, scribe and cut it about an 1/8" larger, grind to fit and Weld. As you pointed out, the partial problem is the shrinkage caused by the Weld-you can planish the Weld flat with a Slapper and Dolly. I generally will put enough tacks to hold the piece, then grind the Welds down to within a 1/16" (front and back), planish and do it all again, a few Welds at a time. This will stretch the Metal back into shape without letting the shrinkage get out of hand-if you do too many at a time it can be a bear to get the Metal flat again.

I am going to fill in the Holes in my Dash also, however I have decided to smooth the entire Dash, so, I am going to cut out what I don't want and put a new, one piece patch in-the reason I am going to do it like that is that I want a clean unwelded area to bore the new holes in without dealing with the welded areas (which are harder to drill and a Hole Saw can cut cleanly)-
01-06-2008 08:06 PM
joeford
36 Ford Dash

I want to change the size and number of gauges on a 36 Ford Coupe Dash.

Can I merely cut and weld in the existing holes and re-cut for the new ones or is there a better way than metal fill?

I'm not a seasoned welder, but it seems that cutting a couple of circles and laying a series of tack weld would not be that difficult. Do I need to be concerned about metal shrinkage?

I know there are gauge clusters available that cover the old holes, but I prefer to install direct to the old dash once filled in...

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 03:49 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.