Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Suspension - Brakes - Steering> bleeding new brake system
User Name
Password
lost password?   |   register now

Thread: bleeding new brake system Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
04-28-2008 10:48 PM
68NovaSS Great! Let me know when you have pedal, he he. Good luck!
04-28-2008 09:21 PM
dar130 WoW... thank You so very much... Gravity is a great thing...
Bleed 3 cylinders in sort order.. then I ran out of time for the last one...
Really, gravity worked great...
04-28-2008 02:56 PM
dar130 thank YOU so much for the advice !
I'll start over using the old method of pushing the brake pedal, I'll post back with how it goes..
04-28-2008 11:58 AM
47 Coupe Some of the bubbles that you are seeing may be coming from the bleeder screw threads. I've run into that more than once
04-28-2008 09:09 AM
68NovaSS First of all, you need to bleed the wheel furthest from the MC first, then work to the closest, the left front. With new lines, disconnect the lines and let them gravity drain until you get flow, with the cover off the MC. You could probably drain all 4 at the same time, reconnecting them as they start flowing fluid. Do that to all 4, then on to the bleeding procedure, always starting with the furthest wheel from the MC, the right rear and work to the nearest, the left front. As always when bleeding, ensure the MC doesn't run dry.

Also, make sure your bleeders on the front calipers are on top. If you have the calipers reversed, good chance they aren't. They'll never bleed if not at the top.
04-27-2008 06:15 PM
dar130
bleeding new brake system

'65 chevy P/U 1/2 ton
I just install a new complete brake system, front and rear tubing, switched from front drums to discs and drums on the rear.
I bench filled the MC as instructed, installed it, installed the new tubing to the the MC and proportioning valve. Now, I can not get the air out.
I was using a vacuum tool I rented to bleed the system.
After pulling a cup of fluid from the front left calliper, it was still full of air bubbles. I removed all of the lines to the other brakes and plugged them, trying to isolate the system to just the front left caliper. Still lots of bubbles..
I double checked all connections that they were tight.
Help, what am I doing wrong ?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 05:58 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.