Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> '62 chevy drive train
User Name
Password
lost password?   |   register now

Thread: '62 chevy drive train Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
07-13-2008 11:42 PM
bigjune62 that's a .5" spacer, sorry if i mistyped
07-13-2008 11:31 PM
327NUT You got me on the 5" spacer??? anyway with the 700R4 the best performance upgrade would be to change out that 3.08 and install a set of 3.73's. Calculations show with your tires....3.08 = 2069 rpm
3.73 = 2506 rpm
or even a 4.11 = 2761 rpm ....you would still be able to cruise all day long, my pick would be the 3.73 or something close.
07-13-2008 05:31 PM
59 el camino
62

Sounds like a pretty good combo to me. Personally would have put a bit more cam in the engine, however, I tend to like a bit more rump rump. My 59 has a similar 283 with a turbo 350 and 308 rear gears. Just replaced the 454 for economy reasons. Aren't x frames a ***** to work with?
Good cruzin.. John
07-13-2008 05:11 PM
bigjune62
'62 chevy drive train

I'm new to building motors, so here goes, My current project is a "62 chevy impala convertible and this is what i've done so far,
bored block .030 over installed stock compression pistons
polished crank and installed new bearings
installed rv cam with advertised int. lift .281 ex. lift .296
duration int. 204 ex. 214
lobe center int. 107 ex. 214
installed a pair of "462" heads with mild port work, hardened seats, port matching.
performer 2101 intake
performer 1406 carb. .5" phenolic spacer
2 inch rams horns port matched to heads opened up to 2.25 at collector flange
2.25 dual exhaust with a pair of magnaflow mufflers (no crossover/ equalizer pipe, kinda hard to do with an "x" frame).
pertronix ignition timing at 35 degrees total advance all in at 2500 rpm.
rebuilt 700r4 trans
new driveshaft with billet center support and slip yoke rear shaft
rebuilt stock rear end with 3.08 gears
24.5" tall rear tires

I'm still working on little details on the car and I'm wondering how this set up should run, I'm making this car strictly a cruiserand trying to keep everything as "stock looking as possible.I failed to mention that evrything but machine work, exhaust and trans. were done in my garage.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 09:17 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.