Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Cam question
User Name
Password
lost password?   |   register now

Thread: Cam question Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
08-19-2008 11:39 PM
F-BIRD'88 Do you know the specs of this cam?
There are so many good off the shelf cams available that one will be very close.
If you do not know the specs you could find out the specs using your block and a degree wheel+ dial indicator or run the cam on a cam doctor.

Critical specs are duration @.020" duration @.050" duration @.200"
peak lobe lift, Lobe separation angle, intake valve closing point @.050" lifter rise. Rocker ratio and valve lash. With this information, I bet you can get a $270 to $350 off the shelf replacement that will make within 98% +/- power and torque.
A junk or defective harmonic balancer will also casue excessive distributor gear wear.
08-19-2008 11:23 PM
53deluxe thanks I had heard that at one time but wasnt sure if it was true ( the repairable dist. gear ) I would think with the cost of a replacement of this cam it should have the pressed on gear I have to call Jones in the morning I choked when I talked to them about a replacement cuz it was in the ballpark of $850 for the same grind cam
08-19-2008 11:17 PM
F-BIRD'88 Check camshaft end play and distributor height. (intake manifold) and the oil pump. High oil pressure will put more stress on the distributor gear.
The cam can be repaired depending on what core it is.
"Street roller" cams have a pressed on section on the end. The distributor gear and last bearing journal are cast iron (like a flat tappet cam) and are pressed onto the end of a roller billet (street roller) if Jones Cams cannot repair it contact Crane Cams. The block can be modified to increase/direct oil flow to the cam distributor gear.
08-19-2008 10:56 PM
53deluxe it was fine when I got it. running the motor for about 20 mins to set the lash and break in the lifters is what ate it up a little and its not a cheap hyd cam its a Jones custom grind solid roller
08-19-2008 10:38 PM
F-BIRD'88 You got it cheap cause its pooched. Any wear on the gear will surely bite into the soft bronze distributor gear. If you don't mind eratic spark timing and bronze filings all thru your motor, go for it. Stock up on some spare gears.
New hyd roller cams are not that expensive.
08-19-2008 08:58 PM
53deluxe
Cam question

hey guys I have a custom grind cam in my bbc that when I tore down the motor I noticed it has little bit of chewing on the dist. gear I've since then bought a bronze gear my ? is is the cam still useable it looks like it ate in about maybe half the thickness of a fingernail

I'd like to use this cam since one its a custom grind two it made my motor into an animal and three I got it real cheap from a friend that builds off shore race boat motors

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 05:31 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.