Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> vortec heads on a 406, can it be done on pump gas?
User Name
Password
lost password?   |   register now

Thread: vortec heads on a 406, can it be done on pump gas? Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
09-14-2008 11:31 AM
406 ss monte that would be me too.

i'm about ready to pull the 406 short block, & put in the factory vortec short block & use with the vortec heads. i would hate to screw up my 406 pistons from detonation. the 350 would be better suited with the heads anyways
09-14-2008 06:19 AM
CNC BLOCKS NE Here is a similar link with some good info.
http://speedtalk.com/forum/viewtopic.php?t=12353
09-13-2008 09:00 PM
406 ss monte How did people run double hump heads on 400's? Their 64cc chambers & need a lot more timing. I've seen several over the years with flat tops & double hump heads & run on 93 pump gas. what's the difference?

just so everyone knows. i already have the vortec heads. their not costing me a cent other than springs & having guides machined. that is the only reason i want to use them. FWIW, i took the exhaust valves out to check the seats to make sure their not the one's with the big seat that restricts flow & their not.
09-01-2008 01:25 PM
ScoTFrenzel There is no practical difference between iron and aluminum for heat dispersion. Dyno tests prove it. A few milliseconds is just not enough time for heat to transfer. MOST of the heat goes out the exhaust.

Remember roller cams lose 8* due to lash.
Keep that LSA down to 106*.
.040-.050 squish distance is critical.
Soft-edge everything in the chamber/piston.
Timing curve will be critical as will mixture control.
Water injection is a good idea.

I ran an 11/1 '70 350/350 on 91-93 with water injection. Vortec heads are better.
You could also take some meat out of the chambers.

I suggest looking into the "head grooving" threads on this forum. It works. Automotivebreath is the "expert".

Remember the higher the rpm, the less "clock time" for detonation to occur.
Good luck, be prepared to buy race fuel.

Enginequest makes replacement Vortec heads in different sizes. Check that.
09-01-2008 12:24 PM
DoubleVision You may pull it off then if you followed the guidelines I said. However, I would get more opinions from others in here that may have already did the same combo.
09-01-2008 12:19 PM
406 ss monte it's a 5.7 rod motor & the pistons i'm useing are sealed power L2489F.

how did people get by with double hump heads? i've seen plenty of flat top 406's with double hump heads. i've used 67cc heads before without any issues, but i figured it up at 11.52 with 64cc heads.
09-01-2008 12:13 PM
DoubleVision With a tight quench, timing slightly on the low side, a slightly rich mixture, and coolant temps in the 180 degree range you might pull it off, but I wouldn`t hold my breath, especially if it has the stock 5.565 rod lenth.
In many cases, and this arguement has went on and on, it doesn`t detonate in the low rpm ranges so the driver thinks it don`t in the upper rpm ranges, but they don`t understand, the cam is bleeding off a lot of the cylinder pressure during low rpm use, then there isn`t the time for it to in the upper rpm ranges, so the engine could be detonating and due to the noise of the engine, exhaust and etc. It`s very difficult to hear. By the time it`s figured out the engine is usually gone.
09-01-2008 11:23 AM
406 ss monte
vortec heads on a 406, can it be done on pump gas?

i have a 406 with forged flat top pistons that i was going to put a set of afr 195 cc heads on with 75cc chambers. i'm selling the afr heads because i need cash to finish my garage, so now i need a set of heads. i have a set of 906 vortec heads, but they are 64cc chambers. i'm figuring 11.52, this is how i'm figuring it.

4.155 bore
3.75 stroke
4.200 gasket bore
.040 gasket thickness
5cc valve reliefs in the pistons (could be more or less)
.005 deck height.

is this to much for 93 octane? i'm thinking of a cam in the lines of 240-250 @.050 with anywhere from a 106 - 110 lobe separation.
the heads being cast iron is what worries me. aluminum would probably work, but i don't know about cast iron.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 03:04 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.