Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Engine Swap Help!!!
User Name
Password
lost password?   |   register now

Thread: Engine Swap Help!!! Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
09-04-2008 07:15 PM
tomslik
Quote:
Originally Posted by crazytown
The reason I am debating about swapping the heads out is because the heads on the 350 are the older type "fuelie heads" which are no doubt good heads for performance, but are made from the older engine technology for running on leaded gas. There is a risk of burning out the exhaust valves of old technology engines if operated with unleaded gasoline in heavy constant service. This is because old technology engines relied upon the lead in the gasoline to coat and protect exhaust valves from the extreme heat of the exhaust.

want to know what I'D do?
i'd run 'em 'till they needed a valve job,THEN worry about it.

what casting # on the heads?
if they have accessory bosses, chances are they've been induction hardened...
09-04-2008 03:17 AM
crazytown
Update.....

The reason I am debating about swapping the heads out is because the heads on the 350 are the older type "fuelie heads" which are no doubt good heads for performance, but are made from the older engine technology for running on leaded gas. There is a risk of burning out the exhaust valves of old technology engines if operated with unleaded gasoline in heavy constant service. This is because old technology engines relied upon the lead in the gasoline to coat and protect exhaust valves from the extreme heat of the exhaust.
09-03-2008 07:51 PM
tomslik
Quote:
Originally Posted by crazytown
The motor in the Camaro is the 305 TPI (tuned port injection) 305ci, 190hp engine (RPO LB9) The 305 TBI (throttle body injection) was used in the Z-28's from 1982-1984. In 1985 Chevy came out with the famous IROC-Z, introducing the TPI system taken from the Corvette.
The compression ratio will increase when the 305 heads are put onto the 350 block. The 305 heads have smaller combustion chambers then the 350 heads. There are many factors that can change compression ratio, combustion-chamber volume, the deck height (the height of the piston above or below the block deck), the head-gasket volume, and the piston design that will either add volume (a dished piston) or subtract volume (a domed piston) from the combustion chamber.
In an article about a 305 TPI to 350 TPI swap the changes needed include:
bigger injectors,
Knock sensor,
ESC (electronic spark control) if equipped),
ECM (depending on year),
and PROM (programmable read only memory)
true, didn't see the thing about swapping heads.
and that brings me to why would you swap heads?
a little creativity on the center bolts on the intake and you got it...
09-03-2008 07:32 PM
crazytown
Info Update

The motor in the Camaro is the 305 TPI (tuned port injection) 305ci, 190hp engine (RPO LB9) The 305 TBI (throttle body injection) was used in the Z-28's from 1982-1984. In 1985 Chevy came out with the famous IROC-Z, introducing the TPI system taken from the Corvette.
The compression ratio will increase when the 305 heads are put onto the 350 block. The 305 heads have smaller combustion chambers then the 350 heads. There are many factors that can change compression ratio, combustion-chamber volume, the deck height (the height of the piston above or below the block deck), the head-gasket volume, and the piston design that will either add volume (a dished piston) or subtract volume (a domed piston) from the combustion chamber.
In an article about a 305 TPI to 350 TPI swap the changes needed include:
bigger injectors,
Knock sensor,
ESC (electronic spark control) if equipped),
ECM (depending on year),
and PROM (programmable read only memory)
09-03-2008 04:01 AM
tomslik
Quote:
Originally Posted by crazytown
I recently purchased a 1986 Camaro IROC-Z, Z28. It has a 305 TPI engine with a 700R4 trans. I have a carbuerated 355 built for another project that I want to put into this Camaro now. The motor in the Camaro is the stock 305 190hp TPI engine (not the H.O). The 355 is a 350 bored .030 over, with a mild cam, 2.02 fuelie heads, pete jackson gear drive, torker 2 intake, & holley 600 cfm carb. My questions are:
Should I convert the car over to run the 355 carb. motor or swap the intake & heads off the 305 to make a TPI 355?

How would the TPI swap affect my compression, hp, and performance?

Any and all info. and comments would be appreciated.
only way the compression will change is if you drop a screw down one of the ports

put a timing chain in it,larger injectors and probably a 350 MAF (if they're different), undoubtably a rechip of the puter..

after reading closer, are you sure it's tpi rather than tbi?
09-03-2008 03:56 AM
tomslik
Quote:
Originally Posted by va4cqd
the geardrive and tpi don't mix
at least the knock sensor ain't gonna like it....
but there's ways around that...
09-02-2008 07:59 PM
va4cqd the geardrive and tpi don't mix
09-02-2008 07:32 PM
crazytown
Engine Swap Help!!!

I recently purchased a 1986 Camaro IROC-Z, Z28. It has a 305 TPI engine with a 700R4 trans. I have a carbuerated 355 built for another project that I want to put into this Camaro now. The motor in the Camaro is the stock 305 190hp TPI engine (not the H.O). The 355 is a 350 bored .030 over, with a mild cam, 2.02 fuelie heads, pete jackson gear drive, torker 2 intake, & holley 600 cfm carb. My questions are:
Should I convert the car over to run the 355 carb. motor or swap the intake & heads off the 305 to make a TPI 355?

How would the TPI swap affect my compression, hp, and performance?

Any and all info. and comments would be appreciated.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 07:06 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.