Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> General Rodding Tech> trans tunnel clearance?
User Name
Password
lost password?   |   register now

Thread: trans tunnel clearance? Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
10-06-2008 09:28 PM
raj4851
Thanks OHD

Thanks for the input, OHD. I hadn't thought of making it removable, but that sounds like a plan. Thanks again, Rod
10-04-2008 09:12 PM
OHD On manual transmissions with floor mounted shifters, I just make a removable cover that comes completely up and out to service/adjust the clutch, shifter, and rods.. If a rollover mounted trans is used you can also service the trans.
09-26-2008 12:34 PM
red65mustang Rod,
on the behalf of all who posted, thank you for saying thanks and your welcome...
09-25-2008 07:44 PM
raj4851
Thanks again

Thanks, red65mustang, I hadn't thought about the heat factor yet, but I'll have to. techinspector1, that's an interesting concept about building a frame around an interior, amazing. Thanks to both of you, Rod
09-21-2008 08:14 PM
techinspector1 It's interesting to note that when us hotrodders build a car, we normally start with the frame and then find a place for everything. When purpose-built tube frame cars are put together, all the components are hung in space at the appropriate positions in the car, then the frame is constructed with curves, bends and whatever else to intersect the components and tie them in. In other words, the frame is the last thing that goes into the car.
09-20-2008 01:28 PM
red65mustang suggestion:

think ahead a step, to be sure you won't run into exhaust pipes/downshift linkage/etc interference....

there is alot of radiant engine and pipes btu's heat that wants to come up thru that big panel into the cab.....
I'd consider making a good part of it a double wall with a open air gap to keep the heat out of the cab....

1/2" to the reflector panel and 1/4-1/2" gap from that to the cab panel is more than plenty good for reflecting/losing 90% of the heat (same as a steel fireplace metal chimney construction)
09-20-2008 11:56 AM
raj4851
thanks again

Thanks for the comment, techinspector1. Sounds like a plan, Rod
09-16-2008 05:03 PM
powerrodsmike That's a trick I learned from the custom motorcycle guys...that's how you position a snug fitting front fender to mount it and maintain enough tire clearance so a rock caught in the tread does not wipe out the paint when it cuts a dent from the inside out of the fender as it rolls through.

Later, mikey
09-16-2008 04:30 PM
techinspector1 "Try laying some 1/4 or 5/16 ID rubber hose over the trans, tape it down, then let the tunnel rest on it while you fit it to the floor."

Excellent!!
09-15-2008 08:30 PM
raj4851
Thanks guys

Thanks, Duece and powerrodsmike for the advice. Thanks for the pictures, Deuce. You've both been very helpful. I'll try the hose thing. It sounds like it would work. Thanks again, Rod
09-15-2008 07:47 AM
cboy
Quote:
Originally Posted by powerrodsmike
Hey Deuce, I like that picture of a wadded up moving blanket you used as a trans tunnel...
Mikey,

That's no moving blanket...that's some sort of well disguised terrorist bomb. Note the electronic detonating device hooked up to it on the right. (Um, or maybe it's just an electric blanket to pre heat his transmission.)

09-15-2008 07:42 AM
Deuce
Quote:
Originally Posted by powerrodsmike
Hey Deuce, I like that picture of a wadded up moving blanket you used as a trans tunnel...Now that's being resourceful
I was trying to show the accelerator pedal being over some and NOT jammed up against the brake pedal. But a 39 does have a wider area to deal with than a Deuce
09-15-2008 01:21 AM
powerrodsmike Hey Deuce, I like that picture of a wadded up moving blanket you used as a trans tunnel...Now that's being resourceful


2 inches is too much. No pedal room. Maybe at the top it would be ok, but at the sides it would cause problems.

I build them with no less than 1/2" clearance from any point on the trans or associated parts. Nothing ever rattles with 1/2" clearance, as far as I know.( hit a bump that will shake the body and motor on their mounts enough to move them 1/2" and the sound of the trans hitting the floor is much quieter than the sound of your head hitting the roof )


Try laying some 1/4 or 5/16 ID rubber hose over the trans, tape it down, then let the tunnel rest on it while you fit it to the floor.

Later, mikey
09-14-2008 11:23 PM
Deuce I usually try for one inch clearance ... have not had any problems with any of my builds.





I dislike a big, over sized tunnel. On a 39 Ford ... it would not be as bad as in a 32 Ford. The smaller the tunnel, the easier it is to get the accelerator over further away from the brake pedal and the steering column.



09-14-2008 09:19 PM
OneMoreTime Moving to general rodding tech..

Sam
This thread has more than 15 replies. Click here to review the whole thread.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 04:00 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.