Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> tri carb help
User Name
Password
lost password?   |   register now

Thread: tri carb help Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
09-18-2008 04:21 PM
oldbogie
Quote:
Originally Posted by kbyounger
I finally got my three deuces on, connected and running!!!! But, when I rev the engine to the point that the secondaries open, the center carb will Pop or backfire as they first open. If I rev it slowly to the point of where the secondaries will begin to open, then the engine "bogs down - or hesitates. I have heard that the floats in the fuel bowls must be set exactly right or the secondary carbs can be too lean or rich... Is this what would cause the center to backfire? Any ideas are greatly appreciated. I'm so close to getting these things running... thanks - kip
Mechanical linkage I presume. This is a common problem. When the secondaries open the total flow area is increased and the instant flow in the primary carb is reduced. This messes up the mixture, the engine will backfire and stumble till it starts to gain some revs to get the air flow in all the carbs up to where main metering is working.

It's a tuning issue. Certainly as you were told; the floats have to be perhaps a bit high, making it easier to draw fuel with less air flow in the venturi. The accelerator pump needs to be played with as well to help hide the lean drop. Secondary throttle timing needs to be adjusted to open the throttles slower and perhaps later in the opening cycle.


Bogie
09-18-2008 03:47 PM
68NovaSS It does sound like a lean condition, so try bringing the end carbs in sooner, not later.
09-18-2008 02:37 PM
kbyounger OK, no its not a real tri power set up, the outside carbs have been altered to make it "tri power." The only thing I know about timing is that the engine is set at 7% advanced, but I don't have the knowledge or tools to watch the timing during acceleration... someone mentioned that perhaps bringing the carbs in later, would help, because it sounds like it is running lean... I can certainly play around with where the carbs come in at, and if that does not take care of it, then I suppose I could then check the float levels... any other thoughts? thanks - kip
09-18-2008 02:28 PM
68NovaSS It's a legitimate tripower setup, no accelerator pumps on the outboard carbs? Cam you being those carbs in sooner and see how that works? You may have a ton of timing coming in early, what's the timing when they start to open? Unless you're accelerating hard, if you have fuel in the bowls free revving it, you're not going to starve it for that split second while transitioning.
09-18-2008 12:44 PM
kbyounger
tri carb help

I finally got my three deuces on, connected and running!!!! But, when I rev the engine to the point that the secondaries open, the center carb will Pop or backfire as they first open. If I rev it slowly to the point of where the secondaries will begin to open, then the engine "bogs down - or hesitates. I have heard that the floats in the fuel bowls must be set exactly right or the secondary carbs can be too lean or rich... Is this what would cause the center to backfire? Any ideas are greatly appreciated. I'm so close to getting these things running... thanks - kip

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 06:08 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.