Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> 6.5 diesal 350 sbc swap ???
User Name
Password
lost password?   |   register now

Thread: 6.5 diesal 350 sbc swap ??? Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
09-20-2008 08:23 PM
dirtslingerrc thanks,, everybody for your replies and great advice, i think i,ll stick a 350 turbo in it , modify driveshaft ,,a floor shifter and keep things simpler,, and less expensive , thanks again FOR YOUR TIME
09-20-2008 10:52 AM
Blazin72 If needed, there are also aftermarket transmission controllers. They aren't cheap though.

http://store.summitracing.com/partde...5&autoview=sku
09-20-2008 09:54 AM
wave1957 To add a little detail to Curtis73, you will see on the driver side of a 4L80E trans a little shaft poking out, on which a shifter linkage is connected/can be connected. You cannot just connect your truck shifter to this shaft to run the trans, it will not work: this shaft is just a switch, allowing you (with your traditional shifter) to tell the computer in which gear you want to be; the actual gear shifting is then done by the computer, inside the trans.
09-19-2008 09:46 PM
curtis73 The 4L80E will not run without a computer, period. But there is good news... I'll get to it in a minute.

The 6.2/6.5 family of engines was designed to basically bolt in place of any chevy engine, so the SBC swap should be a super easy breeze. Just confirm that the motor mounts are the same (or buy the proper mounts) and drop it in place. The bellhousing bolt patterns are the same. Two things you'll want to consider; 1) the diesel typically uses the large bolt pattern on the torque converter, so you'll probably need the larger (168-tooth) flexplate on the SBC. and 2) the diesel torque converter is a low-stall unit that won't be optimized for a gas engine. It will physically work, but it might seem a little sluggish off the line. For that reason you might want to get a stall that is properly matched to your 350

The good news I promised... Hotrodders for years have tried to find cheap easy ways of gettting a 4L80E to work in their old cars. One of the ways they have discovered is to use the computer from a 6.5 diesel. It has to be modified internally somehow, but do a search on some diesel forums and you'll find that the diesel PCM is one of the ways to get a 4L80E to work behind an old-school engine. I don't know the details, but someone in the tranny forum might.

But... I'll say it again, because I know your next question is going to be, "can't I just shift it manually?" or "how can I get it to work without the computer?" You can't. Period. The only thing you can do is install a race-type manual valve body along with some other modifications and then shift it manually.
09-19-2008 09:13 PM
dirtslingerrc thanks, i can slide thru the emissions ,, and it could be a 4l 80e /trans pan is square like a 350 turbo ,,and it will power spin both whells on concrete bridges big time ,,any way i want all that computer junk out complety ,it even has a computer on the throttle , but the 350 sbc is in a 1979 gmc with hei ignition, mainly i justwant the ignition to work ,, or i can rig my own under dash if i have to i want to strip out everything that i can and and have clean engine bay with a 350 ,thanks,
09-19-2008 08:34 PM
Blazin72 I'd have to imagine the diesel got a 4L80E. I might be wrong but a 700R4/4L60 might be a little on the weak side.
09-19-2008 08:29 PM
burnt olds
6.5 diesal 350 sbc swap ???

does it need to go through emission's test ?
09-19-2008 08:03 PM
dirtslingerrc
6.5 diesal 350 sbc swap ???

i have a 1995 gmc sierra / old state vdot truck/ 165000 miles runs excellent except ,a dead miss that might get very expensive,, anyway,,how much trouble to put in a350 sbc. ??will it bolt right in /motor mounts/?? can i use same torque converter and tranny?? its, a700r4 i presume ,3 spd.with overdrive in a half ton truck,, i presume i,ll need a wiring harness too . i thank you all for your expert advice..rick

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 06:37 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.