Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Electrical> Tail Light Light-Bulb
User Name
Password
lost password?   |   register now

Thread: Tail Light Light-Bulb Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
09-28-2008 11:10 AM
timothale
tail lites

A hole saw tends to rip out the metal. For sheetmetal I use the cone type step bit, some companies call it a UNIBIT If you clamp sheet metal between 2 pieces of wood you can get a better hole using a hole saw ... I have a set of greenlee electricians knockout punches ...they work good if the size is right for gages ,..etc..I would do a spot of solder or braze to make sure to get a good ground unless the bulb socket as a ground spade connector for a ground wire
09-28-2008 10:51 AM
matt167 the socket should be crimped in place, so you would just knock the crimps in with a screw driver, no need to drill it.
09-28-2008 10:30 AM
65comet Thanks....one housing has a 1 1/8 hole that the universal socket fits into perfectly. The other hosing has the original fitting that has the spring loaded contacts...

I'd like to make both the same...i want to drill out the existing fitting with a hole saw...

How fragile is my pot metal housing? I'm thinking I need to keep the drill bit speed up and slowly come down on the housing with my press...

or should I leave well enough alone and just have the different sockets?

thanks

g
09-28-2008 10:14 AM
richard stewart 3rd Hi,

1156 for back up bulbs, single filament single contact

http://www.eautoworks.com/product-Led-33243.htm

Rich
09-28-2008 09:22 AM
T-bucket23
Quote:
Originally Posted by boatbob2
Hi,can anyone tell me where i can find a metal taillight socket that will take the gm 1157 bulb??? ive been looking for awhile,,,thanks in advance.
Any parts store should have them. There are also different depth sockets. MAKE SURE the bulbs have clearance between themselves and the lenses or you will melt the lenses. I made this mistake once long ago and was a very expensive one !!

Chet
09-28-2008 09:06 AM
65comet Thats exactly the type of info I was looking for! Would I also use the 1157 type bulb for my back-up lights too?

Thanks all....
09-27-2008 05:31 PM
timothale
sockets

I rewired a 36 Pontiac last summer and bought metal sockets at the local parts store in the trailer parts rack about $6 for a pair. Later bought 6 at a quarter a piace at a surplus store,
09-27-2008 05:26 PM
matt167 IMO, there is nothing better than these sockets for what you want.. they work great, and take 1157 bulbs, altho the solder point on the side interferes with them, so you need to scrape it off or get a quality bulb that does not have that. I had a crapped out socket in my '65 Rambler, I simply knocked the crimp in with a screwdriver, and installed in less than 5 mins, and it's good as new. $24 is steep for a socket, but IMO, there is no inbetween, there are the parts store variaty's which sometimes are ok, or these

http://www.ronfrancis.com/prodinfo.asp?number=RR-33
09-27-2008 05:15 PM
406 bug go to Tailightking.com . just type in in your brouser
09-27-2008 04:43 PM
boatbob2
tail light socket..

Hi,can anyone tell me where i can find a metal taillight socket that will take the gm 1157 bulb??? ive been looking for awhile,,,thanks in advance.
09-26-2008 10:27 PM
timothale
taillites

going to bigger amp bulbs or halogen can overheat and melt plastic lenzes. the metal sockets can be hard to find but when I put them in older cans i solder or braze a spot to make sure to get a good ground. also some tail lites look funny at night if you have the bulb in the wrong orentation I check the original or place them with the fillament horizontal.
09-26-2008 10:17 PM
406 bug
Quote:
Originally Posted by T-bucket23
If the tail and brake are in the same bulb, an 1157 will probably be your best bet.
CHet

Chet is right- the original tail bulb was an 1157.
09-26-2008 08:01 PM
T-bucket23 If the tail and brake are in the same bulb, an 1157 will probably be your best bet.
CHet
09-26-2008 12:34 PM
65comet
Tail Light Light-Bulb

I have a tail light housing that is missing the original built in socket. While in the process of trying to find that socket, somebody said to use a universal socket and pick the type of light bulb you want.

I like that idea, however, I'm not sure what type of light bulb I might wants...I can only think that I'd want it very bright.

Can anybody suggest what type of lightbulb I might want to look at?

I'd replace both the tail-light/brake light and reverse light sockets.

thanks

George

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 08:15 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.