Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> 1973 429 Thunderjet worth updating?
User Name
Password
lost password?   |   register now

Thread: 1973 429 Thunderjet worth updating? Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
10-01-2008 03:32 AM
AmericanPackMule
Heads 385's...

Quote:
Originally Posted by T45965
Looking or valued comments regarding this engine. It has been balanced/bluprinted with new hardware, but the heads stayed the same (190HP rating). Does it make sense to put new 10:1 or 9:1 heads on it, with new manifold / carb / cam to increase the HP? I really was interested in about 350-450 hp ratings. It seems I could get into this for about $3500 vs a new crate @ $6500. But looking for your advise. Thanks. Steve
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~


The big PORT Heads C.J / S.C.J. Were For 7 + G's - Lower Vacuum @ 3 Gs.
For 450 H.P. @ 7,000 R.P.M. Put a Dominator carb. + Electronic Ign. + Big cam, 5.0 L. / 290 Dur. on 9.0:1 Combustion. Premium Gas.
09-30-2008 05:00 PM
onebadmerc Get a Ford Motorsport timing chain and set it at 0 degrees or you can do like I did on my 78 460 and set it at 2 degrees advance. This little change from the stock retarded timing chain will make quite a bit of difference. If you have the D2VE head on your 429, get rid of them, they are the worst heads ever made for a 429-460 engine. If you want more compression look for a set of D0VE heads, theses are small chamber 429-460 heads. The most common head for a 429-460 is the D3VE heads. The D3VE have larger closed chambers than the open chamber D2VE heads which are detonation prone. All standard 429-460, C8VE, D0VE, D2VE, D3VE heads have the same ports this excludes fuel injected 460 heads, 429 CJ, SCJ and 429-460PI and 429BOSS. In 1973 Ford went to the sled fulcrum design rocker, prior standard 429-460 heads had rail rockers. All 429CJ, SCJ and 429-460PI had adjustable conventional rockers with pushrod guild plates.
09-30-2008 04:24 PM
T45965 Thanks for the comments! Very much appreciated. S
09-30-2008 03:47 PM
oldbogie
Quote:
Originally Posted by T45965
Looking or valued comments regarding this engine. It has been balanced/bluprinted with new hardware, but the heads stayed the same (190HP rating). Does it make sense to put new 10:1 or 9:1 heads on it, with new manifold / carb / cam to increase the HP? I really was interested in about 350-450 hp ratings. It seems I could get into this for about $3500 vs a new crate @ $6500. But looking for your advise. Thanks. Steve
Better heads would potentially help but knowing what's on it by casting number would pin point if they need replacement. This engine is right on the edge of where Detroit got lost, some of these came with good stuff and others were confused. Keep in mind that new heads on a $3500 engine will do a lot to close the cost gap to a $6500 engine.

Bogie
09-30-2008 11:12 AM
FEDDO I think they were all retarded. just use a timing set that had different keyways. depending on your cam, install st up.
09-30-2008 11:08 AM
barnym17 Best bang for the buck would be a 69 or 70 timing set.Ford retarded the timing of the cam about 8 degrees for emission reasons in 71 I beleive. Using the early set will free up a good bit of low end tourque.
09-30-2008 09:23 AM
T45965
1973 429 Thunderjet worth updating?

Looking or valued comments regarding this engine. It has been balanced/bluprinted with new hardware, but the heads stayed the same (190HP rating). Does it make sense to put new 10:1 or 9:1 heads on it, with new manifold / carb / cam to increase the HP? I really was interested in about 350-450 hp ratings. It seems I could get into this for about $3500 vs a new crate @ $6500. But looking for your advise. Thanks. Steve

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 02:14 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.