Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Body - Exterior> fisheye with epoxy
User Name
Password
lost password?   |   register now

Thread: fisheye with epoxy Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
12-13-2008 02:03 PM
OneMoreTime I would block it a bit and do not use any more W&G and then shoot the epoxy..filler is kinda odd in that it will vary in density and you will get something looking like fisheyes when you shoot it..let the epoxy induce..wait a few minutes after you mix it and then shoot it..I never reduce epoxy unless it is for a final seal coat and that is only so it will lay out a bit slicker..

Sam
12-13-2008 12:16 PM
chas350 This is on a van door with external hinges, I am thinking that contamination caused by spray lube over the years may have been the cause.
I do wipe off the w&g remover with a dry p towel. But the filler holds it and I forgot to hit it with compressed air like I usually do, because I had a visitor.
So, should I just block it down a little and clean again, blow dry then hit it with my MS182 surfacer?
thanks guys
chas
12-13-2008 11:07 AM
BarryK W&G will do that every-time, filler may have looked dry but filler is a sponge and can hold a W&G for 20-40 minutes after it looks dry depending on humidity.
That is why its not a great idea to wash filler.
12-13-2008 10:44 AM
mechEcwru Don't let it evaporate... Make sure you wipe it dry. I do small sections at a time and wipe it with a clean rag really good before it evaporates. If you let it evaporate the wax or grease will be left on the panel.
12-13-2008 10:13 AM
302 Z28
Quote:
Originally Posted by chas350
Barry I cleaned it twice.
Could it be caused by the w&g remover not fully evaped?

chas
Only if you allowed it to evaporate rather than wiping it dry.

Vince
12-13-2008 09:18 AM
chas350 Barry I cleaned it twice.
Could it be caused by the w&g remover not fully evaped?

chas
12-13-2008 09:12 AM
BarryK Did you clean the filler with wax and grease remover?
12-13-2008 09:08 AM
chas350
fisheye with epoxy

Hi fellas
I have fisheyes over my filler/putty after one coat of 10% reduced transtar epoxy. I was going to apply MP182 surfacer next, but dont want to have a problem later.
what should I do?

chas

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 12:29 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.