Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Suspension - Brakes - Steering> Pinion Angle ?
User Name
Password
lost password?   |   register now

Thread: Pinion Angle ? Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
12-17-2008 12:52 PM
ScoTFrenzel
Quote:
Originally Posted by user151
Well I'm confused... in the last referenced link, centerline shows a mailburacing drawing and says it does not show pinion angle (he is correct, it shows pinion to driveshaft angle), but then he shows an Inand Empire drawing that shows the same thing!

What I gather is that the pinion and trans output shaft angles should be parallel (that is, equal but opposite sign angles) to eliminate vibration .... AND (here's the kicker) the U-joint angles should be 1 (min) to 3 (max) degrees to minimize U-joint wear.

Setting the former does not guarantee the latter... it would depend on how long your driveshaft is. Am I missing something? Can someone clarify this ror me?

Thanks, Tom
You not only have a vertical displacement but also a lateral displacement of shafts centerline due to pinion offset slightly to one side of the vehicle.
The trans shaft centerline and the differential pinion centerlines should be parallel, theoretically, but in practicality the pinion angle points down 1 1/2 to 4* in static (non running) conditions because power load will cause rear suspension joint flex, or leaf spring twist. In such cases the theoretical centerline is zero under the anticipated load. It will not always be correct because load and suspension travel constantly vary.
The maximum joint angularity is 3* in any driving conditions.
12-13-2008 04:41 PM
Centerline
Quote:
Originally Posted by user151
Well I'm confused... in the last referenced link, centerline shows a mailburacing drawing and says it does not show pinion angle (he is correct, it shows pinion to driveshaft angle), but then he shows an Inand Empire drawing that shows the same thing!

What I gather is that the pinion and trans output shaft angles should be parallel (that is, equal but opposite sign angles) to eliminate vibration .... AND (here's the kicker) the U-joint angles should be 1 (min) to 3 (max) degrees to minimize U-joint wear.

Setting the former does not guarantee the latter... it would depend on how long your driveshaft is. Am I missing something? Can someone clarify this ror me?

Thanks, Tom
Actually those parameters are pretty easy to set up in almost any vehicle. In a "T" bucket or something similar that has a very short driveshaft it may require some trans angle adjustment but generally speaking those settings are pretty easy to achieve. As long as you're setup falls within those you should not have a problem. Keep in mind though that this is a "street" setup. Setting up pinion angle for racing is different.
12-13-2008 03:53 PM
user151 Well I'm confused... in the last referenced link, centerline shows a mailburacing drawing and says it does not show pinion angle (he is correct, it shows pinion to driveshaft angle), but then he shows an Inand Empire drawing that shows the same thing!

What I gather is that the pinion and trans output shaft angles should be parallel (that is, equal but opposite sign angles) to eliminate vibration .... AND (here's the kicker) the U-joint angles should be 1 (min) to 3 (max) degrees to minimize U-joint wear.

Setting the former does not guarantee the latter... it would depend on how long your driveshaft is. Am I missing something? Can someone clarify this ror me?

Thanks, Tom
11-26-2008 04:19 AM
JDracing57
pinion angle

Thanks for the info.
11-25-2008 12:40 PM
Triaged Here are some of the first results of a search of the Knowledge Base

http://www.ls1.com/forums/showthread.php?t=16319
http://www.buickperformance.com/Pinion.htm
http://www.hotrodders.com/forum/axle...lp-106161.html
http://www.hotrodders.com/forum/pini...eet-62742.html
http://www.hotrodders.com/forum/pinion-angle-56457.html
11-25-2008 10:25 AM
JDracing57
Pinion Angle ?

I am putting a 9 inch in a ford ranger with approximately 400 HP what should the pinion angle be?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 01:15 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.