Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Interior> Help with custom gauge cluster 87 caprice
User Name
Password
lost password?   |   register now

Thread: Help with custom gauge cluster 87 caprice Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
01-11-2009 09:59 PM
DENCOUCH
Plastic is cool!

Tomorrow I am mounting the dash that I modified. In my '74 Chevy, all of the gauges are pooled together on the left side & looks funky and outdated.

I grabbed another plastic dash and hacked up the two sets and made my own that gives me what I am looking for... all of the gauges marching along the top of the dash, left to right.

Since I don't have A/C in my truck, two of the gauges fit there np, I don't have a working OEM radio, so I built a little cubby hole for junk & stuff.

A shot of gray wrinkly-coat paint & itis looking pretty sharp. Low bucks project.
01-10-2009 06:41 AM
the-gauge-guy You guys are on the right track. Make the part out of something stiff, like aluminum, then find a screenprinting place that can laser cut. They can screen a new cluster face and laser cut it to fit exactly. Thats what we do all thetime. Most custom gauge shops can handle this. The artwork is the big cost.

Mark
01-07-2009 08:44 AM
DanTwoLakes I like Sam's suggestion, but I would make the pattern out of chipboard (easier to modify and tweak) and back up the aluminum with plastic like sheet nylon, UHMW polyethylene, or UHMW polypropylene. The plastic will fabricate very easily with woodworking tools. This will give you a very stable surface and a solid base for the gauges.
01-06-2009 04:50 PM
OneMoreTime How I would go about something like that is to pull out the old dash panel and then make myself a template of the area to be filled out of thin plywood like 1/8 inch plywood..It may take several stabs at it to get something pleasing in appearance..figure out just where you are going to attach the new panel and fix some brackets or you may be able to drill some screw holes to fasten the new panel..layout the gauges and lites and then cut the holes in the ply..when all this is satisfactory then take a piece of aluminum at least 0.060 and engine turn it and then cut and drill the holes in the aluminum..assemble the gauges to the new panel and install it..I try and find some socket head cap screws or nice stainless or chrome torx screws about a #8 to fasten the panel..looks kinda high tech and hotroddy when done..

If you like you can do a fiberglass dash panel as well..just depends on your fabrication skills and what you like..
Sam
01-06-2009 04:18 PM
973kgt
Help with custom gauge cluster 87 caprice

I have an 87 caprice. The dash only has an 85mph speedo with a fuel level gauge. Im swapping in a t-56 transmission so I need a tach. What I want to do is pull out the gauge pod/cluster unit and make some sort of sheetmetal? gauge panel and cut out some holes to put in an aftermarket speedo,tach, fuel and a few other gauges so I can keep an eye on all the vitals. My vehicle is no longer computer controlled so I dont need all the dummy lights it has. Any suggestions on how to get started and if I should use sheet metal or something else. I will have to add my own lights for turn signals and hi beams so I know when they are on. If sheetmetal is preferred would it be wise to rubber mount it to keep vibrations down?

Thanks and I hope I didnt confuse anyone.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 12:52 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.