Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic -- Hot Rod Forum

Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Freshly Rebuilt sbc 355 cranks over hard
User Name
lost password?   |   register now

Thread: Freshly Rebuilt sbc 355 cranks over hard Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Please select your insurance company (Optional)


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
02-09-2009 06:43 PM
KA67_72 I'll probably catch some grief for this, but I have a motor that likes a lot of timing also. I just have an ignition kill switch. I kill the ignition, start cranking, and flip it back on. I've tried all kinds of things short of a super starter. The old girl doesn't deserve that kind of money. If I retard the timing to where it will start, it just falls on it's face.

02-09-2009 05:38 PM
Originally Posted by weirdbeard
My guess it the timing is to far advanced. Pull the wire to your coil and crank it over. I bet it will turn over fine with no spark.
i agree with weirdbeard on this my 408 acted the same way.oh just wondering what distributer are you running. nice 67 weirdbeard i have one to.
02-09-2009 05:22 PM
johnsongrass1 Check your battery and grounds. these things cause all kinds of grief.
02-09-2009 04:49 PM
weirdbeard My 67 Camaro liked that advanced timing too, but it was cranking over so hard I started breaking starters.

Easy enough to test though. Let us know what you find.
02-09-2009 04:20 PM
awoodman Well the thing is it purrs like a kitten when started. I'll give that a try though. thanks
02-09-2009 04:17 PM
406 bug You may want to check your timing. Put it back where you had in on initial start and go from there.
02-09-2009 04:16 PM
weirdbeard My guess it the timing is to far advanced. Pull the wire to your coil and crank it over. I bet it will turn over fine with no spark.
02-09-2009 04:04 PM
Freshly Rebuilt sbc 355 cranks over hard

hey guys, i just built my first engine. It's a 1989 chevy 2-bolt main block bored .030 over. It's got a 9.7:1 compression ration and i put on new cast iron heads w/ 64cc chambers, new bearings, machined crank, rods, etc. It's all been put into a short bed 1985 S10. I put everything together, checking clearances and everything very carefully with the use of a information book on building small block chevys. I primed the oil pump before starting the engine. I just started the engine for the first time last week and it cranked right over easily when i jumped it with my jeep wrangler, putting out 14v or so when it's running. It ran, although we had to restart it a few times to get the timing right. Now when I've tried to start it up recently (maybe the 5th time or so, it started cranking over hard. Is this because the rings and valves have broken in and become fully seated and sealed and made it much higher compression? Do engines with a higher compression ratio like this usually take more volts or amps to crank over than a normal battery/alternator can dish out? Im kind of worried because it basically barely cranks over, im lucky to be able to crank it over one or two times, although that usually does start it up eventually if i take pauses in between cranks.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -6. The time now is 07:09 AM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 1999 - 2012. All Rights Reserved.