Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Suspension - Brakes - Steering> 1965 Chevy II Nova Steering Problems
User Name
Password
lost password?   |   register now

Thread: 1965 Chevy II Nova Steering Problems Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
03-23-2009 09:22 AM
Double_v23 OK so my original guess was correct on this. The spindles are wrong. Someone used 74 and up spindles with steering arms that are not interchangeable. So I need to get some earlier ones.

The tie rods do not follow the lower control arms and this is what is causing all my problems.
03-16-2009 09:39 PM
Double_v23 Maybe he did say the lower control arms. He mentioned that the chevelle and camaro spindles were different and I believe the chevelle ones were the correct ones. I might have that backwards as well.

As soon as it quits raining I am going to get some pics together.
03-14-2009 08:12 PM
Mike H I would think the tie rods need to be in the same plane as the lowers control arms, that has always been the rule of thumb. Did he tell you what will interchange for the spindles?
03-14-2009 11:34 AM
Double_v23 I have gathered a little more information from a local guy that does these swaps quite often. Apparently you can run front steer spindles reversed like mine are but you have to use certain ones that have the steering arm in the correct postion.

Also the tie rods have to be parallel with the upper control arms.

Any input on these statements?
03-08-2009 07:51 PM
Mike H I would guess they are off of a 70 up camaro etc. they were front steer and would bolt into the Chevy II and give you the issues you are having. You couls try a 68-74 nova spindle they are rear steer and yuo can adapt a disk brake system to them easy.
03-08-2009 07:25 PM
Double_v23
1965 Chevy II Nova Steering Problems

I bought a 65 Nova off of a guy (he is clueless) and he had put "the 5 lug conversion" on it. It has disc brakes on the front, I believe he may have taken them off of another vehicle. Here is the problem,

It needed strut bar bushings and a serious alignment. I replaced the bushings but when I went to line up the toe and camber it got kind of strange. First off, the camber is too far off to even come close with the eccentrics. Then, whenever you go forward and hit the brakes the car takes a dive and the tires toe out to a ridiculous angle. Go in reverse the front end rises up and the tires toe-in to the same angle. No matter what I do I can't get the wheels centered in the wheel wells.

One problem that I found is that the spindles are marked LH and RH and as far as I can tell they are on the wrong sides. But the brakes and tie rods are mounted and functioning correctly.

What I am wondering is if it is possible to just swap sides and flip the spindles upside down to get them to work. (This seems to be the one thing that would eliminate most of the angle problems)

Or is it possible that someone took spindles off of a front steer car and stuck them on this car...which is rear steer, then stuck them on opposite sides so that it would mount up?

Any insight into how these disc brake swaps are usually done on these cars would be helpful. Also if you know which car I can get a direct bolt-in off of please let me know.


Mark

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 10:03 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.