Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Garage - Tools> Drill press clamping
User Name
Password
lost password?   |   register now

Thread: Drill press clamping Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
03-28-2009 08:35 PM
4 Jaw Chuck He-he, my spidey sense was tingling.

A medium size 6" vee block works great for drill press work.

I've also used 4 Jaws and 3 Jaws for holding round work on the drill press, they are easy to clamp. It really depends on what you have laying around.

Vee blocks are quite universal tools for holding work on milling machines and drill presses, having good clamps is essential to avoid slippage however.
03-22-2009 05:17 AM
oldred Most 4 jaw chucks are independent and should work quite well to accurately hold a part on a drill table (make sure it is of the plain back variety however so it will lay flat) but the setup would be a lot faster and easier with a good milling quality cross slide table. This would be even more of a consideration if the part being drilled had to have multiple holes drilled in a pattern. If this is to be an operation that you plan to do often then using a lathe chuck, while it would work, could get to be a hassle.
03-21-2009 09:56 PM
Mike H
Quote:
Originally Posted by awert
I'm lost, I can see using the 2X cross slide, but how can the 4 jaw chuck be of much use????? Unless all 4 jaws are independently turned. but still not very useful without a lathe........
I use a 4 jaw chuck to hold pistons in my Bridgeport all the time. I f I need to mill any off of the top I clamp the chuck to the table and if I need to gas port them I put the 4 jaw in the super spacer so I can gas port above the top ring land from the side.

All of my 4 jaws are independent but I have seen one that was a scroll type.

Mike
03-21-2009 07:26 PM
awert
Drill press clamping

I'm lost, I can see using the 2X cross slide, but how can the 4 jaw chuck be of much use????? Unless all 4 jaws are independently turned. but still not very useful without a lathe........
03-21-2009 06:25 PM
oldred
Quote:
Originally Posted by OneMoreTime
How about bolting or clamping this to the drill press table..

http://grizzly.com/products/5-4-Jaw-...-x-8-TPI/H8042

that is more what I had in mind..

Sam


That would work and should be very accurate, it would just require a bit more set-up time. Actually that 4 jaw chuck is probably a good idea from a cost standpoint because it should be as accurate and stable as a good compound milling table and there would be no chance the part would wiggle around. I have to admit those cross slide vises like the one in that link can sometimes be a bit sloppy but I have that one and it has been pretty good, but then again from HF you just never know from one tool to the next.



This may be more like what you need, this one would be stable enough even for a mill.


http://www.use-enco.com/CGI/INSRIT?P...&PARTPG=INLMK3
03-21-2009 04:59 PM
Mike H You could get a small compound table and pick up a used 4 jaw off of ebay with an oddball backing plate for not too much money. The compound tables are pretty accurate as far as drilling goes.
03-21-2009 03:46 PM
OneMoreTime How about bolting or clamping this to the drill press table..

http://grizzly.com/products/5-4-Jaw-...-x-8-TPI/H8042

that is more what I had in mind..

Sam
03-21-2009 03:43 PM
OneMoreTime I may try that one..i have a similar type now but it is "wiggly" and try as i may it does not get much better when I adjust it..I am getting the drill bit with a morse taper shank for this to eliminate the slop in the normal drill chuck..

Thanks
Sam
03-21-2009 02:47 PM
oldred This is a good one for a drill press and they have some cheaper ones also, this is a little better quality than the "Central Forge" brand and although I would not want it for a milling machine it works great for a drill press.


http://www.harborfreight.com/cpi/cta...emnumber=94276
03-21-2009 02:36 PM
OneMoreTime
Drill press clamping

I need to bore some holes that are accurate and all I have at this time is a drill press..what I need is a better clamping fixture to attache to the table of the drill press..I was thinking of something like a 4 jaw chuck bolted to the drill press table..do they make such a thing..?? the holes need to be centered accurately in the workpiece..

Thanks

Sam

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 05:33 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.