Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Vortec head conversion - EGR
User Name
Password
lost password?   |   register now

Thread: Vortec head conversion - EGR Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
03-29-2009 12:20 PM
chevy_c10 Curtis, I have one question about the cam that basically serves as EGR and still keeping the EGR valve. If the cam lets in exhaust gasses, and then the egr adds in exhaust gasses, won't there be way too much? Or, will the cam just let in exhaust gasses at low speeds and not highway speeds where the EGR will kick in? Still just a slight bit cloudy on the subject. Also, what do you think the performance difference between the carb vortec intake w/out egr and the tbi vortec intake with egr would be?
03-29-2009 12:43 AM
curtis73 Find someone with a sniffer. Some old shops have them for carb tuning. You can really clean up a tune that way.

Additional cam can clean up the NOx that an EGR would normally create, but the increased compression associated with larger cams kinda negates that. Plus larger cam often equals increased HC emissions.

I would personally keep the EGR if you can rig one up, but truly, emissions is largely in the tune. Many of us LT1 guys have gotten away with pretty hefty power numbers and still pass OBD2 emissions in CA. A common setup many of us have done is fully ported stock heads, ported intakes, cams in the 230 duration range, headers, and compression in the 10.5-11 range and with careful tuning it still passes CA emissions testing for 96 vehicles.

I would say focus on the tune first. Down the road if you want to continue cleaning it up then you can add EGR and other smog magic
03-28-2009 10:06 PM
chevy_c10 It will be tested as the 76 but I am one of the few that wants to clean up the engine as much as possible.
03-28-2009 09:58 PM
va4cqd what emissions requirements will the truck be tested to? as a 76 or the year the TBI is from?
03-28-2009 09:55 PM
chevy_c10 va4cqd I will have a custom chip done by Brian over at tbi chips. He is the one that suggested to use that cam with the vortecs.
03-28-2009 09:53 PM
va4cqd TBI will probably freak out with that cam
03-28-2009 09:52 PM
chevy_c10 That is great news then. At least I do not have to worry about spending the money and figuring out how to plumb the gasses. I want one day to have my truck updated with modern systems for economy and power but still cut down on my emissions. Sure going to be an improvement over my "smog" engine now.
03-28-2009 09:45 PM
F-BIRD'88 I would think so and I would not go larger if emissions are important to you.
I ran a similar summit 1103 cam 214-224-112-.442-.465 in my old 350 vortec motor and it was very good on exhaust emissions on the smog test, even with no cats.
It passed easily.

Cats would have reduced that even further.
03-28-2009 09:34 PM
chevy_c10 I do intend to upgrade the cam. The one that I would like to use is the comp cams 12-262-4 with 262 intake/ 270 exhaust and at .050 has 218 intake/ 224 exhaust and the lift with 1.5 rockers is .464 intake and .470 exhaust and finally the LSA is 114 degrees. Is this enough to create the self- egr effect?
03-28-2009 09:05 PM
F-BIRD'88 If you'll also be changing the camshaft out for one with more duration and overlap than stock, then you can forgo the EGR plumbing. The increased overlap of the cam results in a internal self EGR effect at low engine speeds.
03-28-2009 08:48 PM
chevy_c10
Vortec head conversion - EGR

I am going to be swapping some vortec heads onto my 76 C10 pickup in the next few months and I want to keep my EGR. I know there will be those who say just ditch the egr but I am wanting to eventually update most everything on the truck and pass emissions. We do not have a visual test, just the gas analyzer test. My question is this, how is the exhaust gas plumbed to the intake. I am aware that I will have to weld a pipe into my #5 or #7 header pipe. However, does that pipe run to the top or the bottom of the intake and if it is to the bottom of the intake, how does that work? Does there have to be a hole drilled through the heads or the block to run the pipe through? Any insight would be greatly appreciated. I have been searching on this for a few days but am coming up empty handed. By the way, the truck has been converted from carb to TBI so the intake I will get will have a place for an EGR.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 10:28 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.