Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> '77 Nova swap 6 banger for v-8
User Name
Password
lost password?   |   register now

Thread: '77 Nova swap 6 banger for v-8 Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
04-15-2009 01:59 AM
sandiegopaul My last ride before building this Corvette, was a '70 Nova. While it was a V8 car to begin with, (307) and had the auto matic trans, I went through a lot of drive train changes after selling the 307 and building my 350.

First, I went through a couple of Turbo 350 transmissions. I had the OEM one built twice until it blew up on a 6500RPM 1-2 shift. Then I went to a Turbo400 and never had another issue. I had to get a different driveline made for the 400.

Then I blew up the OEM 7.5" Rear end. Many pieces. I got a 12-bolt housing from a Gen1 Camaro, to replace the ol' 10 bolt with. Yet another custom driveshaft of course. BUT - That drivetrain lasted for years under much abuse. I ran 4:11 gears and let me tell ya: That Nova ran like a rocket! Wish my Vette was as light and as immune from SMOGGING as that good ol' Nova. I miss it.

That '70 Nova was a great & fast car. I drove it through 7 states before selling it.
04-14-2009 11:11 PM
jimfulco http://novaresource.org/axle.htm is a good reference source for Nova drive trains. The "rules" were sometimes broken, however. Occasionally, due to parts availability problems, they would use a stronger rear or trans than spec called for, in order to keep the assembly line operating, but it was only once in a while.

http://www.oldsmobility.com/10bolt-tech.htm has pics of how to tell an 8.5" rear from a 7.5".

The Camaro/Firebird 8.5" rear will NOT bolt into a Nova. It's too wide, and the spring perches are too far apart.
04-10-2009 12:19 PM
fast68 hi there

well, 77 seems to be the oddball year in that the th350 did come behind the 250 engines. i had a 77 250 nova and it had the t350. i can look in the gm data options ordering sheets for the 77 novas that i have here and make sure. regardless of the trans though it will bolt to any chevy v-8 engine.

have fun
04-09-2009 11:27 PM
ericnova72 I've done this same swap to a '76 so I can give you some pointers. The motor mounts on the frame remain in the same place, you will just need the metal "shell" engine bracket(motor mount cup) for a '75-87 SBC car. Truck mount cups are taller and won't fit correctly. Trans behind the six is more likely to be a TH250 (mine was) so look at it close. A TH350 will bolt in its place with no trouble. The six cars frequently came with the spindly 7.5" rear(mine did), but the V8 Nova or Camaro/Firebird 8.5" rear is a bolt in. The 7.5 is easy to identify by the two 3/8" long "fangs" that stick down from the casting below the rear cover at about the 4 and 8 o'clock position. The 8.5" will have a 1", square cornered 1/2 block at the same spots. Distributor and alternator wiring will need to be re-routed, and the power steering pump will need to have it's brackets changed to V8 type. Alternator and starter can be re-used, you might have to change the throttle cable. I was building a street/strip car so I left the sixer front springs in, and it did sit low with a V8. Sway bar was the same as a V8 car, if you want a bigger one look to the '70-81 Camaro/Firebird. The rest (belts. hoses, etc.) is stock V8 Nova. It is a pretty easy swap, done in a day if you have all the parts.
04-09-2009 09:30 PM
jagurit
'77 Nova swap 6 banger for v-8

Looking at swapping out the 6-banger in my '77 Nova for probably a 350. What kinds of mod's, if any, am I going to need to take into consideration? I'm getting ready to basically rebuild the front-end and all the parts (ball joints, bushings, etc.) seem to be the same regardless of engine size. Some specific questions:

1) Wondering if the springs are the same and if I should beef up the stabilizer bar?
2) I think the motor mounts will work (that is, I wont need to do any welding/cutting, etc.)?
3) It has an auto trans which I'm assuming ( ) it's a Turbo 350 and will mate with a 350?
4) Need to swap out the rear-end? Not sure what the gearing on it is. Is there a relatively easy way to find out? It sure seems to wind out now - don't know for sure if that's the gearing or because it's just a 6 cyl?

Anything else I need to account for, please advise.

Thanks,
Jag

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 11:08 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.