Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> rear main seal
User Name
Password
lost password?   |   register now

Thread: rear main seal Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
05-16-2009 09:11 PM
chevynut
Rear Main Seal

Just wanted to say thanks to all that replied. It worked out good, old seal out and new seal in just like you said.
05-14-2009 07:18 PM
curtis73 The 6.5 is a one-piece rear main. The biggest headache is getting to it (remove tranny, flexplate) but then its just prying out the old one and putting the new one in.

Its a bit tricky getting the old one out. I like to take a sharp knife and cut the rubber out of it so I can get some space to pry. I like using an aluminum or brass drift to punch the old one out, that way I don't risk scratching the crank or the bore.

Installation can be done by carefully tapping around the perimeter, but you risk hitting the crank or deforming the seal. I suggest finding a piece of PVC or steel pipe that is the right diameter and using it as a big round seal driver.

Coat the crank's sealing surface with oil so you don't damage the seal, and you can coat the outside of the seal with oil too. Some guys use silicone, but I've never had one leak on the outside of the seal where it presses in.
05-14-2009 07:13 PM
my87Z this isn't for the 6.5L but it should of some help

http://flashoffroad.com/Diesel/62Mai...earingseal.htm
05-14-2009 07:09 PM
fast68 hi there

i found this regarding the 6.5L RMS removal:


Remove the oil pump and rear main bearing. Just for precautionary measures, replace the oil pump with a new one. Inspect the rear main bearing face and crankshaft mating surface for any excess wear / mars. Pull the seal out of the bearing cap use a small screwdriver or awl to remove the seal that is still in the block. Clean all mating surfaces of the oil pan and engine block for the reinstallation.

hope that helps maybe
05-14-2009 06:35 PM
chevynut
rear main seal

Hi, I am writing to find out the correct way to remove and replace a one piece rear main seal in a 6.5L diesel. I have not had the chance to do one yet. I have an idea on how to do it but want to be sure. Do I drill hole and pull out with puller and then just tap in the new seal? Thanks in advance.

chevynut

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 05:40 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.