Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Valve Stem Seals
User Name
Password
lost password?   |   register now

Thread: Valve Stem Seals Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
05-16-2009 08:38 PM
fast68 yep thats all it needed and its a very commmon issue, the seals dont last forever with all the heat and oil cooking them and making them so brittle they fall apart.

most old untouched engines have this problem.

my 91 s-10 4.3L truck does it very badly big cloud of blue smoke at startup for a second at 196k miles but i dont care, its fine, just is the stem seals missing.


good luck
05-16-2009 05:20 PM
mightycarlo10 Well i put umbrellas on and installed new o-rings and it started and didnt smoke at all. So i guess its fixed for now.
05-16-2009 08:19 AM
mightycarlo10 I dont hav ethe umbrellas, thats what i thought i was missing. The next propblem is, if i install these umbrellas and new seals, is that going to stop the leak? I dont want to get it all back together to find out that i need to take it apart again.
05-15-2009 10:15 PM
fast68 use the flat round ones like you have on all the valve stems

i always use umbrellas only on the exhausts

good luck
05-15-2009 09:25 PM
cobalt327
Quote:
Originally Posted by mightycarlo10
I have the little plastic o-rings, but is there supposed to be a retainer or umbrella type thing? *snip* i noticed that most of the o-rings werent in the right spot
What you have is what's used from the factory. Sometimes, the O-rings get displaced when the springs are removed. It's also easy to get them installed on the stem but not in there groove at installation, as well.

Do you have the metal "umbrellas" or "deflectors" that fit over the tops of the springs? They fit over the spring, under the retainer and overhang the OD of the spring by an inch, give or take. These are needed to let the little O-rings have a chance at controlling the oil, IMHO.

Image below, left is an exhaust spring with the oil deflector and an exhaust valve "rotator"; right is an intake w/deflector and no rotator (rotators used on exhaust only- when they are used at all).
05-15-2009 07:34 PM
mightycarlo10
Valve Stem Seals

This is probably a stupid question/ screw up on my part. These are 882 heads from a 75 Monte Carlo. I never checked this when i built the car, which i probably should have, but am i missing a part of the seal? I have the little plastic o-rings, but is there supposed to be a retainer or umbrella type thing?

I was planning on replacing the heads because the car smoked like a train and burned a lot of oil. I noticed it was strange that every single valve was leaking oil and all looked about the same amount. I just figured the heads were completely shot. So i was takin the valve springs off to swap to the new heads... then i noticed that most of the o-rings werent in the right spot, they were all up by where the first pic position is. Here's a couple of pics:






Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 01:15 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.