Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Transmission - Rearend> 1961 buick torque converter
User Name
Password
lost password?   |   register now

Thread: 1961 buick torque converter Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
05-19-2009 10:28 AM
mmerlinn You probably have a Cast Iron Dynaflow transmission. It should say Dynaflow on the side of it. If so, you must dismantle the converter to remove it.
05-19-2009 10:09 AM
h0trod389 took the TC cover off, and inside... low and behold... there was a bolt that held the TC into place!
flipped the flywheel and slapped the trans back in!

some linkage, replace some fuel line, she should be runnin by the weekend..


thanks for your help mike!
05-18-2009 03:50 PM
powerrodsmike Good news about the quick fix for your ring gear from someone with real experience. (told ya I didn't have a clue)
No Santa Maria trip for this guy this year...but if you are taking 101 past Gilroy, feel free to stop by.

Later, mikey
05-18-2009 03:36 PM
h0trod389 i was able to get one of my old tymer friends on the phone, he said if i unbolt the TC cover, i will be able to get to 3 snap rings that are inside the torque converter, however. if i pull the cover off, i can flip the ring gear for the starter. watch out for the o-ring that seals the TC, if its good, put it back together and be done with it!

get off work @ 5, so i will hopefully get the tranny back in today!

im about an hour from ya, but thats 2 hrs, minus the time we take bull****ting that i can have it done and runnin again

you going to santa maria this weekend?
05-18-2009 11:44 AM
powerrodsmike From what I gathered from reading the text of the manual, (without having the trans to look at), there are a snap rings and planetary gearsets and springloaded clutch packs in the TC...almost like half of the stuff that resides inside a normal transmission is in the Buick TC...

If you are close to Gilroy, you are welcome to come borrow this book.



Later, mikey
05-18-2009 11:26 AM
h0trod389 yes! the TC does have bolts that surround the TC, ill take them off and hope that works...

ive never messed with this either, so i thought i get some insight before i taking apart stuff!

thanks mike!
ill post again after i work on it
05-17-2009 09:45 PM
powerrodsmike I'm looking in my 55-63 chiltons manual, and it says the stock transmission for a 61 LeSabre is a Dynaflow. Does the TC have bolts holding the case together? In my book it says that you have to disassemble the TC on the trans to get it apart.
I've never taken one of those critters apart, so I have no clue.

Later, mikey
05-17-2009 09:08 PM
h0trod389 done tried that, didnt work....almost like its retained with a c-clip or somethin
]
05-17-2009 08:05 PM
boatbob2
torque converter...

HI,not sure about a Buick,but if you push it in,and turn it to the left,it MIGHT come out.
05-17-2009 07:44 PM
h0trod389
1961 buick torque converter

hay guys im workin on a 61 buick lesabre, with a 364 nailhead and what i believe is a 3 speed hydramatic.

the problem is that on the ring gear around the torque converter, where the starter contacts with, are all chewed up. (no i didnt knaw on them!)

it looks like if i flipped it around, i would have proper starting, until the teeth started wearing out again.

but... i cant seem to get the torque converter out of the trans!

is there a special way to pull it?

thanks for all your help!

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 10:06 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.