Have any 1 out there use schneider cams for the chevy SBC or any motor, if so how do you like it and do you have video to here Schneider Race Cams I was thank about buying
between 1 of these cams.
I was looking for the very lopy idle, witch would be the better cam and why... I can build the motor but not good at matching parts that work good together...
Schneider cam help...
And witch cam would be better to run in a 327/30 over 210cc runner heads 58cc chamber 2.02 / 1.60 valves, black nascar air gap rpm manifold 1.6 rockers flat top
pistons with 4 valve relief in the pistons, holley carb bp carb that flows 734 cfm, muncie M22 tranny, 373 gearing in 82 camaro.
grind -
Part Number: 02005
Grind Number: 288-96H
Intake Duration (gross): 288
Exhaust Duration (gross): 296
Intake Duration (.050”): 230
Exhaust Duration (.050”): 238
Intake Valve Lift*: .485"
Exhaust Valve Lift*: .492"
Lobe Separation: 108 Intake Valve Lash: .000"
Exhaust Valve Lash: .000"
RPM Range:
3000-7200
Based on 1.5 Rocker Arm Ratio
next cam
Part Number: 0202
Grind Number: 299H
Intake Duration (gross): 290
Exhaust Duration (gross): 308
Intake Duration (.050”): 230
Exhaust Duration (.050”): 248
Intake Valve Lift*: .510"
Exhaust Valve Lift*: .525"
Lobe Separation: 107
Intake Valve Lash: .000"
Exhaust Valve Lash: .000"
RPM Range:
3200-7000
Based on 1.5 Rocker Arm Ratio
I been checking the net but can't find any chevy motor with Schneider cams install.
Any help out there...
between 1 of these cams.
I was looking for the very lopy idle, witch would be the better cam and why... I can build the motor but not good at matching parts that work good together...
Schneider cam help...
And witch cam would be better to run in a 327/30 over 210cc runner heads 58cc chamber 2.02 / 1.60 valves, black nascar air gap rpm manifold 1.6 rockers flat top
pistons with 4 valve relief in the pistons, holley carb bp carb that flows 734 cfm, muncie M22 tranny, 373 gearing in 82 camaro.
grind -
Part Number: 02005
Grind Number: 288-96H
Intake Duration (gross): 288
Exhaust Duration (gross): 296
Intake Duration (.050”): 230
Exhaust Duration (.050”): 238
Intake Valve Lift*: .485"
Exhaust Valve Lift*: .492"
Lobe Separation: 108 Intake Valve Lash: .000"
Exhaust Valve Lash: .000"
RPM Range:
3000-7200
Based on 1.5 Rocker Arm Ratio
next cam
Part Number: 0202
Grind Number: 299H
Intake Duration (gross): 290
Exhaust Duration (gross): 308
Intake Duration (.050”): 230
Exhaust Duration (.050”): 248
Intake Valve Lift*: .510"
Exhaust Valve Lift*: .525"
Lobe Separation: 107
Intake Valve Lash: .000"
Exhaust Valve Lash: .000"
RPM Range:
3200-7000
Based on 1.5 Rocker Arm Ratio
I been checking the net but can't find any chevy motor with Schneider cams install.
Any help out there...