Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Cheap BB chevy roller lifter conversion--like small block?
User Name
Password
lost password?   |   register now

Thread: Cheap BB chevy roller lifter conversion--like small block? Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
05-31-2009 08:30 AM
ap72 swapping lifter types is done sometimes, and has worked some of the time.

Another possibility is calling up a cam company and asking them what they can custom grind- they may be able to grind you a smaller soild roller with less intense lobes to make it a torque monster and lessen the maitenance.
05-31-2009 08:08 AM
383ram I have considered a solid rollers, unfortunatly i am not looking at big cams--which is what alot of solids are. Stuff right near stock sizing is what i am looking at-- i want lots of torque and lower rpm power. Plus, after 15 years of messing with this stuff like valve adjustments, i'll admit--i am lazy. But one way or another, even if i have to pay for it in the end, it will have a roller cam. I just dont trust these oils today--even approved ones for flat tappet cams. Its just alot easier (and cheaper) to do on a small bock rather than big block.

However---ever run solid roller lifters on a hyd roller? Years ago on flat tappet stuff Crane told a friend of mine that the cam doesnt know what lifter is on it. Told him if he was going to do that, run .002-.005" lash and it should work good----and it did. Dont see why you couldn't do that with roller stuff. Just crazy ideas running through my head.......
05-31-2009 07:38 AM
ap72 Just go with solid lifters and be done with it. It'll be cheaper and perform better. You will have to lash them about every third oil change, but if that is too much then you probably don't need to be asking this question in the first place.
05-30-2009 08:01 PM
Guy Hiltz
Quote:
Originally Posted by JAKEJR
Years ago I recall comparing BB and SB lifters side by side and found that the oil holes were at different heights.

I don't know what difference that would make or if the difference only occurred with the two lifters I was using for comparison. Just something to check and consider.

I also recall that one company - forgot which since it was so long ago - had the same part number for both BB and SB lifters, but lately I've seen them listed with different part numbers. Don't know why.

Jake

West Point ROCKS!
As far as aftermarket roller lifters go,except for the tie bars,early small block lifters are IDENTICAL to Mark IV big block lifters.
Guy
05-30-2009 07:35 PM
Chevrolet4x4s Check with competition products
Shane
05-30-2009 10:57 AM
JAKEJR Years ago I recall comparing BB and SB lifters side by side and found that the oil holes were at different heights.

I don't know what difference that would make or if the difference only occurred with the two lifters I was using for comparison. Just something to check and consider.

I also recall that one company - forgot which since it was so long ago - had the same part number for both BB and SB lifters, but lately I've seen them listed with different part numbers. Don't know why.

Jake

West Point ROCKS!
05-30-2009 08:50 AM
Guy Hiltz I dont think that I would grind any material away from the lifter valley area,JMO.
Guy
05-30-2009 07:33 AM
383ram YEs, talking the early small block and MarkIV big block. Yup, figured the lifter diameter was the same so why not.

BUT, i went out and looked at the block this morning and noticed i would have to grind clearance around one of the lifters (dont remember if it was exhaust or intake), for the link bar to go around it, it would mean taking alot out of the block in the edge of the valley. I'll have to see if i can get a pic of the block later to show. I just dont know if it is safe to grind that much out.
05-30-2009 07:17 AM
Guy Hiltz Do you mean the early 265-400 small block into the Mark IV big block ?? If so,the lifters are identical except for the tie bars,so theoretically,your idea could possibly be made to work.If you are going from a newer model small block into a newer big block,it may also work,but I'm not certain about that.
Guy
05-30-2009 05:49 AM
383ram
Cheap BB chevy roller lifter conversion--like small block?

As some of you know, you can retrofit factory hyd roller lifter parts into a non roller lifter small block with very minimal work. Is there parts and pieces that can be done to the big block too? I have all the small block stuff here, lifters are same bore size, a little cutting and welding of link bars wouldnt bother me, but i am unfamiliar with factory BB parts. Like a small block, its just hard to justify $500 for a set of lifters when their may be cheaper alternatives.

Just found this:



I wonder if i could use this with the same 3.8 lifters(shorter than stock 350 roller lifters) that are used in the conversion of small blocks?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 10:15 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.