Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Exhaust port alignment
User Name
Password
lost password?   |   register now

Thread: Exhaust port alignment Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
06-16-2009 07:22 PM
k-star
headers

You don't need to buy new headers or mess around with plates. This is a common problem with the small block Chevy. If you measure the square inch area of the exhaust port exit and the square inch area of the header i am sure the header is going to be bigger.

Keith
06-16-2009 06:12 PM
oldbogie
Quote:
Originally Posted by ssmonty
Hey you guys,
I'm looking for opinions/options on header to exhaust port matching. The main things I'm concerned about on my set-up are limited gasket material left at the bottm of the ex. port on the head, and the headers look to be restricting the ex. in the middle of the two siamesed ports on a sbc head. You will probably have to look at the pics to see what I'm talking about. I don't mind the bottom of the ports not being as large as the header opening, like an anti-reversion step, but where there is not much space between the ports it looks like the headers will be restricting flow, you can see where they overhang the gasket, and may be more subject to burning out. I planned on using a Felpro 1205 gasket(shown). I don't think I can grind and re-weld between the header tubes, but maybe someone else could? I'm sure if they did it would damage the ceramic coating, but would it be worth it? Any of you know of a spacer/adapter, kind of like a 1/4" thick steel gasket. or a smaller empty header flange, that I could grind to blend the exhaust port to the header, and where to get it?
I would be grateful for any, and all replies.
ssmonty
Wrong headers you need D port headers like these https://paceperformance.com/index.as...rodID=82064%20

You don't want the headers hanging into the port, this really screws up flow so bad you might as well keep OEM manifolds on the engine. If you can't afford to replace the headers, the next best thing I can recommend is a set of adapter plates. They are available commercially but are pricey for what they are costing about a hundred bucks. You can duplicate them with a suitable length of 3/8's aluminum plate, a saw, drill, and die grinder.

Bogie
06-16-2009 04:59 PM
ssmonty
Exhaust port alignment

Hey you guys,
I'm looking for opinions/options on header to exhaust port matching. The main things I'm concerned about on my set-up are limited gasket material left at the bottm of the ex. port on the head, and the headers look to be restricting the ex. in the middle of the two siamesed ports on a sbc head. You will probably have to look at the pics to see what I'm talking about. I don't mind the bottom of the ports not being as large as the header opening, like an anti-reversion step, but where there is not much space between the ports it looks like the headers will be restricting flow, you can see where they overhang the gasket, and may be more subject to burning out. I planned on using a Felpro 1205 gasket(shown). I don't think I can grind and re-weld between the header tubes, but maybe someone else could? I'm sure if they did it would damage the ceramic coating, but would it be worth it? Any of you know of a spacer/adapter, kind of like a 1/4" thick steel gasket. or a smaller empty header flange, that I could grind to blend the exhaust port to the header, and where to get it?
I would be grateful for any, and all replies.
ssmonty

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 10:44 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.