|07-13-2009 06:48 PM|
|FmrStrtracer||I hope you plan on disassembling the entire motor for an inspection. All that metal from the cam is now dispursed thru every oil passage and bearing in the motor.|
|07-13-2009 08:21 AM|
I avoid cams with super fast ramps for that reason.
xtreme or voodoo cam have very fast ramps and are easily wiped out.
Softer break in springs, oil break in additive, and extra oil in the crankcase are a must with cam break ins. Plus you need to run an oil additive at EVERY oil change. (www.zddplus.com).
A heavy truck with stock converter, then I would use an old school compcam 260H or 252H and 9 to 9.5:1 cr with those vortec heads. And use stock springs for the break in.
after a cam goes flat, the engine bearings typically get chewed up. The engine should be pulled out, disassembled, cleaned, inspected, and repaired (new bearings and crank turned).
|07-13-2009 05:40 AM|
FYI for those interested I split this thread moving the sections about adjusting the kick down cable into the Transmission section.
The title of the thread is Kickdown cable adjustment.
|07-10-2009 07:25 AM|
|engineczar||Ditto on Comp Cams. I would say 80% of the cams I use are from Comp and in nearly 30 of building engines I've never had one go flat. As far as them not making power, that has more to do with the person picking the cam and their ability to match it to the rest of their combination as opposed to the brand. They have some great custom lobe profiles if you know what you're looking for.|
|07-10-2009 06:47 AM|
While I've installed far fewer cams than a pro like K-star (not done for a living), I've not had any issues w/Comp's cams. I had a run of three Comp cams right in a row at one point, all fine. The time I've used their cams (not exclusively) spans nearly 30 years- from when they were known as "Competition Cams".
Of the two cams that went south on me, one (Lunati) was because the pivot ball was installed upside down (long story, but not my fault for installing wrong, but I didn't catch it, either...), the other was a BBC (big Crane solid lifter cam) that didn't rotate the lifter on one lobe and this wasn't seen in time at start-up (v-covers were on), or during setting the valves- where it might have been. This engine even had the inner spring removed for break-in.
In both these cases, the cam would have failed- regardless of who made it, IMO.
FWIW, Comp has a nitriding process that is available as an added cost option. IIRC, it was about $100 extra.
|07-10-2009 06:17 AM|
I have probably used more comp cams in engines then 10 guys here put together. I have never had one of them ever go flat.
99% of the time the cam gets blamed and it's another issue.
I have only ever had 2 cams go flat, a lunati and a white box, Both were around the time of the big lifter de-boggle.
|07-10-2009 01:44 AM|
|BugRod||I have been running comp cams in my race motors for years with no problems. On another point mopst cam companies get thier blanks from the same suppliers. I always use an older set of springs when breaking in a new cam, that puts less pressure on the lobes while they break in.|
|07-09-2009 10:33 PM|
|TroyBoy||I've had good luck with Crane,Summit and Comp.I have had 3 Comps, 2 of which I had pulled and used in other engines with no troubles.I also used the lifters that I used with the cams in the correct order.|
|07-09-2009 09:30 PM|
|07-09-2009 08:14 PM|
This cable adjustment effects the internal transmission pressures, and shift points.
I just witnessed a transmission builder chewing out the owner of the engine builder/installer today, about the transmission only lasting for 25 miles, and the kick down cable bracket being wrong for the setup.
|07-09-2009 05:22 PM|
I have never had a problem with Crower, Crane, or Lunati camshafts.
Take your pick.
|07-09-2009 05:14 PM|
|Chevy21||Well, I used the cam lube that they supplied and used a bottle of their break-in lube as well. Ran the cam for 30 min. between 2000-2500 rpm. This cam was not that radical of a cam. I think that maybe cam manufacturers should be changing the process in which they make thier cams if oil companies are no longer putting additives in their oil. These particular cams must be made of soft material or something. Either way, I do not plan on doing business with them anymore.|
|07-09-2009 05:06 PM|
Frankly when using a cam that requires valve springs with a greater force than what a wimpy Gen 1 SBC in a pick up would have had, what you need to do is use these weak OEM type springs for break-in. After getting some time on the engine and getting it dialed, then replace the springs with the high performance stuff. This can be done without pulling the heads with an air compressor to hold the valves shut and a tool for the purpose.
|07-09-2009 04:47 PM|
|Chevy21||Well, we found the problem last night. We took it out for a test drive and found that the motor was also backfiring through the carburetor. We ended up pulling the valve cover and could visually see that the exhaust valve on #8 cylinder was not moving very much. We pulled the rocker and measured the push rod travel with a dial indicator. The intake and exhaust valves next to the bad one measured what they were suppose to at .308 intake and .317 exhaust. The bad exhaust one only measured .175. So anyway, I guess the new comp cam that has less than 1 hour on it shaved a lobe off. Can't say I'll be buying one of those again.|
|07-06-2009 11:40 PM|
Edelbrock also has some jets and rods, etc.
|This thread has more than 15 replies. Click here to review the whole thread.|