Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Transmission - Rearend> How to Remove a Carrier Bearing
User Name
Password
lost password?   |   register now

Thread: How to Remove a Carrier Bearing Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
07-13-2009 05:45 AM
bosco200 Ok thanks I got it off.
07-13-2009 05:35 AM
BOBCRMAN@aol.com If you want to do this job. Here is how the pro's do it.

First separate the shafts. The large knurled collar holds the two shafts together. There is a rubber O-ring inside the collar. This slides off over the splines. Very tight fit and will sometimes break on older shafts.

Most c-bearings are rubber mounted. The rubber is just a molded piece that will pry off with a long bar and some work. Determine front and back. Remove. Then place a bearing pull collar around the metal bearing and press bearing off with a press. A large hammer and chisel will work if no press is available.

Install by sliding new bearing assembly over the splines on the shaft. Then drive it on the press portion of the shaft until it seats against the shaft. I use a long driver. Looks like a piece of pipe with a drive ring welded on.

Replace o-ring and thread collar.

To line up the two shafts for re-assembly. The spline will have a "Skipped tooth" line it up with the grease zerk on the outer piece. Push together.
07-13-2009 03:42 AM
mmerlinn I have replaced several carrier bearings by the roadside with hammer and steel punch (or shaft) to drive them off of and on to the driveshaft.

If you are not sure how the shafts go back together be sure to mark them. If you fail to do that, then all you need to do is line up ALL u-joints with each other so they flex in unison. Wrong line up will cause horrendous noise, vibration, and failure in very short order, sometimes in less than a mile of driving.
07-12-2009 07:10 PM
junior stocker Are you refering to the "support bearing" for a 2 piece driveshaft? If thats it, it's not too difficult. Loosen the knurled ring from the front shaft and separate the 2 piece driveline. A puller makes removing the support bearing easier, but it can be removed without one, and a little creativity. Be sure to mark all the parts BEFORE separating anything so you can put it back together the same way. Most libraries have repair manuals if you don't have one.
07-11-2009 10:37 PM
prostreet6t9
Quote:
Originally Posted by bosco200
How to do you remove a carrier bearing on the Drive Shaft?
Mark the D/L before you pull anything apart!

Can you post a pic of the carrier Brg? On Some of the early style Carrier Brg's you will need to knock out the U-joint to get to the bolt that holds on the yoke next to the Carrier brg, remove the bolt and yoke. Then you can use a press to remove the Brg. Alot of time these are not a TIGHT pressed fit and sometime even pull off by hand.

If it's the later style the Brg, it will just press off after you seperate the D/L. The later style is a tighter pressed fit and you may need use a press or Brg remover to get it off.

If your slip yoke has a Screw on cap don't forget to unscrew it before you try and seperate the D/L's

I woulnd't suggest using a torch ! If you scar up the surface where the Brg is pressed on,the new Brg will spin on the shaft and you WILL have a premature failure.

Again!!! Mark the D/L Before you seperate the 2 pieces! You want to put it back together the same way to avoid any vibration problems.
07-11-2009 10:45 AM
eloc431962
Quote:
Originally Posted by Crosley
I'd suggest not giving bosco any bad ideas... he seems to not know much about vehicle repair and is seeking proper guidance.
I am sorry crosley, I went back and read all of his post, and maybe he should take it to someone who know how, but if for some reason bosco you try this make sure you mark the old bearings location so you can put it back where it was at before, you can mark it with some yellow marker paint or something like that. Thanks Crosley for pointing this out to me . Cole
07-11-2009 10:38 AM
Crosley I'd suggest not giving bosco any bad ideas... he seems to not know much about vehicle repair and is seeking proper guidance.
07-11-2009 10:36 AM
eloc431962 Torch it off. Cole
07-11-2009 10:25 AM
cobalt327 Prob the same truck he's been asking about gearing for:
Quote:
Originally Posted by bosco200
1972 C20 Chevy and it has a 250 Ci V6 with a 4 speed manual transmision and 4.11 rear end
I doubt it has a V6 engine, though.
07-11-2009 10:18 AM
eloc431962 Sometimes they are pressed on the shaft. Cole
07-11-2009 09:58 AM
eloc431962 What are you working on some remove different then others. Cole
07-11-2009 09:55 AM
bosco200
How to Remove a Carrier Bearing

How to do you remove a carrier bearing on the Drive Shaft?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 10:48 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.