Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> I let my timing chain slip and cant find TDC
User Name
Password
lost password?   |   register now

Thread: I let my timing chain slip and cant find TDC Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
07-19-2009 02:25 AM
curtis73 You won't bend the valves that easy. Turning it over by hand won't hurt a thing. Don't go forcing anything, but no worries.

Many times, setting the cams on their marks will let you turn the crank freely. Set your cams and then set the crank. If you hit a valve, don't worry. Just adjust the cam(s) one way or the other until you can turn the crank.

Pull the plugs to make turning easier. That way you're not fighting compression and thinking you're pushing against a valve.
07-19-2009 12:07 AM
Berg valve cover is off.. I can see valves/cam lobes etc... just worried about valve to piston contact trying to find tdc..just don't want to mess up the valves
07-18-2009 08:13 PM
123pugsy I guess the best thing to do is to remove the valve cover and check the positions of the cams.

Don't know if this can help:

Here
07-18-2009 06:54 PM
Berg You can see in the above pic that the two cams are at TDC in the pic( note the colored chain link and the marks on the cam sprocket--
they are no longer in that position.
After the lower chain moved I messed with both the upper and lower and cant figure it out. The yellow dots are teh tdc mark locations where they should be but are not.
I am real paranoid of bending valves... and I did not want to pull the head at this point.

thanks for any suggestions
07-18-2009 06:49 PM
Berg
I let my timing chain slip and cant find TDC

Hope I'm ok asking a Nissan question here.
I have a Nissan 4 cylinder motor with a dual overhead cam . I was just changing the timing chain when I messed things up.
The instructions were to get crank and valves lined up to compression top dead center. No problem. I stuck the crankshaft bolt in and turned it to the timing tdc marks to get ready to pull the chains.
In loosening the crank bolt I spun the crankshaft in reverse rotation within the chain because I had taken off the tensioner and guide( big mistake)... see picture.
My problem now is trying to line things back up because I don't know how far the cranks spun backwards. Anyway I attached a pic- you can see the slop in the chain and in trying to move the pistons I am contacting the valves. Not hrd but enough that I feel the tension.
I'm probably making this harder than it needs be but can someone guide me on trying to get the crank back in sync with the valves. I am overly worried about bending a valve.. maybe they don't bend that easy.
I know what I did wrong just trying to fix it. Making a simple timing chain replacement into a major PITA. Could I have already damaged a valve. Each piston has 4 valves and they are angle in the head. I was going to do a leakdown and comp test when I get things back together.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 02:03 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.