Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Bbc 402 Installing In A 1980 Camaro
User Name
Password
lost password?   |   register now

Thread: Bbc 402 Installing In A 1980 Camaro Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
08-12-2009 04:02 PM
cobalt327 The only way to know for sure if springs are needed in the first place, is to install the engine.

If it sits too low or bottoms out over bumps, etc, add spring rate. In my experience, "correct for the application" OEM springs always sit too high for my taste anyway. I'd look into an aftermarket spring, if new springs are decided on.

If OEM springs are used, you could use Pontiac Firebird Formula/TA springs intended for WS6 cars, or Camaro Z-28 w/F41, w/a bit cut off the bottom- but this tends to be hit-or-miss, and the spring rate goes up when the springs are cut. But it is an option.
08-12-2009 02:21 AM
DoubleVision Since you`ve removed a bit then I wouldn`t bother to change the springs.
08-11-2009 08:45 PM
Glen Rogowski So If I Purchase Motor Mounts For A Bbc I Should Be Ok? One More Question On The Coil Springs. I Will Be Purchasing Headers Aluminum Manifold And Heads Also Deleting The A/c So Do I Still Need To Chang The Coils? The Car Was Already Setting High In The Front When It Had The Sb
08-11-2009 12:22 PM
cobalt327 FWIW, I had no problems with a factory AC-delete, 229 V6-equipped '81 Camaro when I put a 454 into it w/the OEM V6 springs. Used SBC mounts, IIRC, made the engine sit up some compared to the SBC's that were in it at different times (or else vice versa- it's been 20-something years ago), but didn't matter, as I had a T/A scoop that provided extra clearance.

After centering and leveling, I simply welded in the mounts, installed a turnbuckle on the drivers side and let it eat.

Now, if this were to have been a permanent installation as opposed to setting it up to run it for a while before selling it, I'd have done things a bit "neater" .
08-11-2009 11:36 AM
DoubleVision No, the location is the same, but the mounts are different. You`ll need the correct big block mounts. In most cases the big block mounts are offset and lower to give the correct clearences. It would also be a good idea to change the front coil springs to compensate for the heavier big block. Even with big block mounts there still maybe clearence issues.
08-11-2009 11:30 AM
Glen Rogowski
Bbc 402 Installing In A 1980 Camaro

I would like to put a bbc 402 that came out of a 72 chevelle into my 1980 z28 camaro that had a sbc 305. Will the motor mounts have to be relocated?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 10:09 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.