Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Suspension - Brakes - Steering> Ford 8.8 Explorer rearend spring perches?
User Name
Password
lost password?   |   register now

Thread: Ford 8.8 Explorer rearend spring perches? Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
09-17-2009 11:54 AM
chieftain Another reason I made my own was my springs were too narrow for the factory 8.8 perches or ones available that were 3" tube. I needed the narrower perch for the bolt pattern to fit in between my lower spring plates which have the lower shock mount. As long as the centering pin isn't more than 1/2" tall the 2 x 4" will work . If you need a pair made pm me.
09-16-2009 03:58 PM
prostreet6t9 http://www.summitracing.com/search/?...20perchs&dds=1
09-16-2009 02:47 PM
chieftain I used 2 x 4 tubing for the perches I made. Scribed it all out for the centers and drilled my pilot holes, than used a 3 1/4" hole saw (took forever) thru the 1/4 steel on my drill press. Than cut the thing in half.
09-12-2009 06:16 PM
dragfrog23
perch and block in one

You can do something like NEW INTERIORS did once you know the length. Another way is to get a 2x5 or 2x6 cut off the usual length of a lowering block 5 or 6 inches, then measure dead center of the piece, drill a pilot hole through both sides, get a 3 1/4 hole saw and cut your circle. When your finished cut it in half, now you have two identical ones. You can box the ends to make it stronger. Don't forget to drill the hole for the locator pin on the spring. In some cases the rear axle needs to be re-centered anyway, so you can control where it goes too.
09-02-2009 01:34 PM
fasteddy51 Great idea! I need to lower my rearend about an inch anyway. Thanks for the input.
09-02-2009 11:59 AM
NEW INTERIORS I have made some using tubing.. When I set the ride height, I use a 3x2 tubing, notching the top, and cutting the front and back on a angle then cap them off..And drill the centering hole.. I do this when I set one up low..This end's up being the perch and the lowering block all in one..

Here's some my son made for his truck..
09-02-2009 11:39 AM
fasteddy51
Ford 8.8 Explorer rearend spring perches?

I am curious what everyone is using for spring perches when using the 8.8 Explorer rearend. Does Ford offer them loose by themselves? The axle tubes for these rearends is 3-1/4" diameter. I have an Explorer rearend that I have cut off the factory spring perches, but wasn't able to salvage them. It seems like the most common spring perches available is 3", and didn't know if everyone is just using those and grinding them slightly to make them fit, or if someone makes them for the 3-1/4" axle diameters. I am replacing a Nova 10 bolt rearend, and have it mounted on the top of the leaf springs. I used a set of aftermarket perches for it that fit fine. Do the 3" ones fit ok without any mods? Someone told me they fit fine and by the time I weld them, the slight difference in diameter actually leaves a small gap for good weld penetration. I have tried to research this on the forum and internet, but didn't find any definite answers. I have the Ford rearend, but haven't obtained any spring perches yet. Any help would be greatly appreciated.

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 03:29 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.