Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Engine> Welding exhaust manifolds
User Name
Password
lost password?   |   register now

Thread: Welding exhaust manifolds Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
09-07-2009 10:02 PM
sqzbox I assume your going for an all stock restoration, right? Have you checked the wrecking yards for a replacement manifold? I know the 390 is few and rare but, the 360ci. has the dog leg exhaust manifolds I think are the same as the 390 and are still around. they can be found in 70's AMC's and jeeps made before mopar bought them out. If not a stock resto, I can recommend Doug thorley (I think the spelling is right) long tube/tuned hedders. They are based in LA Cal. I built and raced a 71 Javelin for 2 yrs. and the biggest bang for the buck improvement was the headers I put on. I could really feel the gain in the "seat of the pants" over every other performance part I put on the engine. Any other info you need on the engine just e-mail me and I'll be happy to help! SQZBOX
09-07-2009 08:32 PM
campracing yes you need to preheat the part

you will need to bevel the crack out alittle and then weld it you will need to also weld it in three passes just like welding a main joint one root pass then two filler passes one beside the other

but the most important part is you have to ping the weld (hit it with a chipping hammer or a center punch) all over the weld also LET IT AIR COOL DONT cool it off with anything or it will crack.

when you ping it then just let it sit untill it cools off on its own.
09-07-2009 08:28 PM
NEW INTERIORS Read this it may help you...http://www.lincolnelectric.com/knowl...ronpreheat.asp
09-07-2009 08:21 PM
mike69
Welding exhaust manifolds

Guys,

I am in the middle of a rebuild of my AMC 390 and I just noticed a crack in one of the bosses where the bolt goes for the exhaust manifold. Does anybody have any advice for welding something like this? I have a MIG welder and O/A torches and I am a reasonably competent welder around the garage, but I have not tried my hand at welding cast yet. I have the Finch welding book and I read the section on welding cast iron...sounds like he recommends preheating it in an oven and then brazing it with the torch. What say ye?

Mike

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 02:07 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.