Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic
Hotrodders.com -- Hot Rod Forum



Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > General Discussion> Hotrodders' Lounge> Off-Topic> can fan blades in a small house type fan go flat?
User Name
Password
lost password?   |   register now

Thread: can fan blades in a small house type fan go flat? Reply to Thread
Title:
  
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Additional Options
Miscellaneous Options

Topic Review (Newest First)
09-15-2009 04:34 PM
matt167 it's a wire framed table top type fan.. it used to blow air to the point you could feel it for about 10-15' away.. it was a cheap fan I got from the Christmas Tree Shop, prolly made in China, it has developed an out of balance vibration also but not anything major.. guess I can just chock it up to blades too soft like Dave said.. sad thing is, I know my grandparents have a GE fan that was made in about 1940, and it still works/ they use it..


I'v got 1 of these in my shed that has a burnt up motor. the blades attach with a set screw, so I'll pull it apart and get those blades.. it'll save me $15 next year
09-15-2009 07:04 AM
Irelands child Sounds to me like a Chinese (Wally World?) POS to me. If it has aluminum blades, they were possibly made from soft sheet aluminum material instead of some that has some temper. I have some sheet stuff that bends easily then some 6061-T6 that is a b@#$h to bend without annealing - and I have to do some of that today if I have torch gas.

Dave W
09-14-2009 11:21 PM
dinger This is a bathroom type of exhaust fan? Did you check it when it was first used? A lot of the "less expensive" fans have little or no air movement. I've never heard of one with the blades flattening, it would seem the blades wouldn't flatten at an even rate and would be very noisy-out of balance. Ain't saying it can't be done though, one never knows, where was it made?
is it possible it is wired backwards?
09-14-2009 08:17 PM
wretched ratchet Sounds like you got it nailed - - - if it ain't sucking and it ain't blowing but it's spinning then you don't have any pitch on the blades anymore. That's a first for me !
09-14-2009 07:38 PM
matt167
can fan blades in a small house type fan go flat?

I have a fan going in a room on low for air circulation, and never gets turned off.. it's 1 of the wire framed 1's with the aluminum fan blades. been on since probably may..went to clean it earlier today and realised. it no longer blew air except out the sides but it was more like whipping the air from spinning.. held paper to the back and it has 0 suction.. this fan was nearly new and working great when I turned it on in may.. I know it's just a house fan but it's got me scratching my head.. could the blades have flattened out from the constant rotation?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -6. The time now is 06:38 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
Copyright Hotrodders.com 1999 - 2012. All Rights Reserved.