Hot Rod Forum : Hotrodders Bulletin Board - Reply to Topic -- Hot Rod Forum

Register FAQ Search Today's Posts Unanswered Posts Auto Escrow Insurance Auto Loans
Hot Rod Forum : Hotrodders Bulletin Board > Tech Help> Suspension - Brakes - Steering> working on 49 chevy shortbox
User Name
lost password?   |   register now

Thread: working on 49 chevy shortbox Reply to Thread
Send Trackbacks to (Separate multiple URLs with spaces) :

Register Now

In order to be able to post messages on the Hot Rod Forum : Hotrodders Bulletin Board forums, you must first register.
Please enter your desired user name (usually not your first and last name), your email address and other required details in the form below.
User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Please select your insurance company (Optional)


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Additional Options
Miscellaneous Options

Topic Review (Newest First)
11-03-2009 11:51 AM
Originally Posted by anyting but original
I'm starting with just a frame leaf springs mounted "no axles" how can i find the wheelbase and the center of the wheels so that I can sub it and place my rearend any help?
All OEM frames have holes punched or drilled to mount various components that will be the same distance front to rear, spring mounts, shock bracket mounts, engine mounts, etc. On the passenger side, measure from the center of one of the spring mount rivet heads to any punched hole on the front of the frame. Write it down. Now, measure the same point to point on the driver's side. Write it down. If they're close to the same, within a sixteenth inch, you have found the proper front holes that match each other side to side. Now, string your tape from the LR point to the RF point, diagonally. Write it down. Now, string your tape from the RR point to the LF point, diagonally. Write it down. If your diagonal measurements are within 1/8 inch, you're ok to go ahead with this frame. If the measurements are off more than that, the frame has been tweaked. It will need to be put on a frame machine and squared or you will need to find a valid frame to start your project with.

If the diagonal measurements check out, set the frame up on jackstands on a LEVEL surface, with a long level placed across the rear rails so that they are level. Place a third jackstand under the front crossmember and level the frame front to rear by placing a level in the driver/passenger area on top of the framerail. Now, measure from the floor to the bottom of the framerail on each side at the front. This will tell you if the frame is tweaked in the other dimension, sort of like an airplane propeller is twisted. If there is no more than 1/8 inch of twist in the frame front to rear, you have indeed found a valid frame to begin your project. If there's more twist than that, it's back to the frame machine to bend the twist out of it or start with another frame.

Insuring yourself that the frame is valid to begin with will sidestep a ton of problems down the road.

If you will tell us EXACTLY what you are starting with and EXACTLY what your plans for it are, there are lots and lots of guys on this forum who can simplify the process for you. Many of us have "been there, done that" and can save you effort, heartache and money on your project if you will cooperate. What frame? What body? Is this the '49 Chevy pickup that was in the title of your thread? What suspension? Clip(s) from what? Built high with lots of road clearance? Built low to hang up on speed bumps? Onroad use? Offroad use? What motor? What transmission? Street car? Street/strip car? Road race car? Mud bogs? Sand drags? Will you expect the car/truck to handle well on twisty roads? Back and forth to bingo for grandma? Silver State Classic? Bonneville? Dry Lakes? Parking lot Gymkhana? Roadster with the top cut off? Chopped top? Channelled? Sectioned? Front or rear engine? Cooling system? Fuel system? Exhaust system? What wheelbase?(on a clipped truck, place the tires/wheels into the wheelwells with the body on jackstands. Stand back and "eyeball" the front to rear placement of the tires so that it looks right. Measure center to center of the wheels. That will establish your wheelbase). Track width?(Don't choose a clip until you figure out the stock track and the clip track). Tires/wheels? Rat rod? Car show entrant? Fenders or no fenders? Pickup bed or no bed? Emissions?
10-31-2009 06:21 PM
anyting but original
working on 49 chevy shortbox

I'm starting with just a frame leaf springs mounted "no axles" how can i find the wheelbase and the center of the wheels so that I can sub it and place my rearend any help?

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -6. The time now is 10:46 PM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0 PL2
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 1999 - 2012. All Rights Reserved.