|11-04-2009 06:56 AM|
One downside of these type tanks is no baffles so fuel will slosh around. I had one that caused the engine to stall under hard breaking or when stopping at the bottom of a hill.
Just a heads up.
|11-02-2009 06:52 PM|
|NEW INTERIORS||Check your PM..|
|11-02-2009 06:26 PM|
|matt167||oops, sorry bout that.. all clear now|
|11-02-2009 06:15 PM|
|NEW INTERIORS||matt clear your PM, I'm trying to send you one..But it's full..|
|11-01-2009 10:08 PM|
|MAYNARDTRUCKIN||I used a air tank on a trike i helped build. I also have used kegs, spun alum. tanks all have pros and cons. big thing is make sure its clean and empty.|
|11-01-2009 09:34 PM|
|TubeTek||If you come out of the bottom of the tank with your supply line, either roll the tank a bit so the fitting isn't directly on the bottom, or drill the stop out of a compression fitting body so you can slide the tube thru enough to keep the inlet slightly above the bottom of the tank. Otherwise, any and all trash or condensation goes straight into your fuel line.|
|11-01-2009 04:52 PM|
I knew a guy that was into demolition derby and mud trucks. He saw a couple of old style propane tanks in my shop recycle trailer and said they use them for fuel tanks. tougher than fi a mini car or truck tank.
|11-01-2009 07:44 AM|
|matt167||40lb propane tank is an idea.. I would deffinetly fill it with water b4 welding. guess it depends on what I find when I need the tank.|
|11-01-2009 07:11 AM|
|Old Rotor Flap||
Darn.... why didn't someone call me? I should have thought of that.
Thanks for the great ideas.
I notice the spun aluminum tanks offered by Speedway are not recommended for street use. Too thin or non-compliant. Though, I don't know what regs covering (pun?) gas tanks. I'm thinking none since you see so many jacked up trucks around here with their tanks hanging there waiting to get pierced in a rear-end accident.
Maybe someday I'll confess what I was planning for a gas tank. Mine will be (note; future tense) sitting out in the open on the rear crossmember. That makes me a little nervous as I think of it as a target.
Thanks again gents, for food for thought.
|11-01-2009 06:34 AM|
I wasn't going to insult Matt with an admonition like that
|11-01-2009 03:04 AM|
If its got room inside use it.I sell gas tanks for 35.00 all the time .Sold one yesterday and they are the best.CAuse I said so,,
|10-31-2009 10:45 PM|
fill with water
I always fill gas tanks with water when I am going to fix one, sometimes it needs a hose fitting to keep the water level just below where I am welding. A used gas tank should be double washed with hot soapy water a couple of times first. the speedway catalog says the gas cap and filler are aluminum but the last one I got has the steel liller neck so I drilled and tapped the old beer keg .
|10-31-2009 09:15 PM|
|10-31-2009 09:12 PM|
Matt - Why not use a 30 (or 40) pound propane tank. The Clifton Park transfer station gets the 30 pounders regularly - there was one Friday and a couple last week when I was there. My spare 20 (almost new) came from there - and they have many that size but not always the latest version with the triangular handle.
Once you empty it, remove the valve and the top and bottom flanges, you have a nice beginning to weld brackets, fillers, bungs for pickups and a roll over vent.
|10-31-2009 08:09 PM|
|This thread has more than 15 replies. Click here to review the whole thread.|